Code Alarm Automobile Alarm CA 110 User Manual

CA 110 Owners Manual  
 
PASSIVEARMING:  
If the passive arming feature has been selected:  
Turn the engine OFF, exit the vehicle, and close all doors, hood and trunk.  
The dash mounted LED will begin to flash rapidly indicating that the 30  
second passive arming timer has begun. If the LED does not begin to flash  
rapidly, then you have left a door, hood, or trunk ajar. Closing this entry point  
will allow the arming cycle will begin. If any entry point is opened during the  
30 second arming cycle, arming will be suspended. When all entry points are  
closed, the arming cycle will begin again.  
At the end of the 30 seconds, the parking lights will flash once, the siren will  
chirp once, and the dash mounted LED will begin to flash slowly confirming  
the system is armed. If the siren did not sound when arming, then the chirps  
have been turned off. Refer to the section on "Eliminating the Arm/Disarm  
Chirps" shown later in this manual. Passive door locking is a selectable  
feature. If you have the optional door lock/unlock circuit installed, the doors  
may or may not lock passively depending upon the setup during installation.  
PROTECTION WHILE THE SYSTEM IS ARMED:  
Opening any protected entry point, hood, trunk, or doors will cause the alarm  
to trigger immediately. The siren will sound and the parking lights will flash  
for 30 seconds, then stop and continue to monitor all protected entry points. If  
the thief left the door opened, the system will sound for six 30 second cycles  
then shut down, isolate the triggered zone and continue to protect all other  
zones.  
Whenever the system is armed, the dash mounted LED will slowly flash. This  
serves as a visual deterrent to a potential thief. This LED is a very low current  
light emitting diode, and will not cause the battery to drain even if left  
unattended for long periods of time.  
Whenever the system is triggered, the vehicle's parking lights will flash for the  
full siren sounding period. Optional - whenever the system is triggered, the  
interior courtesy light will flash for the full siren sounding period.  
Whenever the system is armed, the vehicle starter circuit is disabled, and the  
vehicle will not start with the ignition key.  
Whenever the system is armed, any strong impact to the vehicle will cause  
the shock detector to trigger the alarm. Any lesser impact will cause the pre-  
detect stage of the shock sensor to emit a few short series of warning tones  
from the siren.  
Page 3  
 
DISARMING THE SYSTEM:  
As you approach the vehicle, press and release the DISARM button on the  
keychain transmitter. The parking lights will flash 2 times, the siren will chirp 2  
times, and the dash mounted LED will turn off.  
If you have the optional door lock/unlock circuit installed, the doors will unlock.  
NOTE: If the passive arming mode was selected at time of installation, the  
dash mounted LED will start flashing rapidly indicating that the system is  
rearming. Opening any door will suspend the automatic arming.  
If the parking lights flashed 3 times, and the siren chirps 4 times, this  
indicates that the alarm system was triggered during your absence. Before  
turning on the ignition key, examine the dash mounted LED's flash pattern.  
The number of flashes identifies the triggered zone. For additional  
information, refer to INTRUSION WARNING SIGNALS found later in this  
manual.  
If the siren did not sound upon disarm, then the chirps have been turned off.  
Refer to the section titled ELIMINATING THE ARM/DISARM CHIRPS.  
SILENT DISARMING:  
As you approach the vehicle, press and hold both buttons of your key chain  
transmitter for 2 seconds.  
The parking lights will flash 2 times, and the dash mounted LED will turn off  
confirming that the system is disarmed. The siren will not chirp. If you have the  
optional door lock/unlock circuit installed, the doors will unlock..  
NOTE: If the passive arming mode was selected at time of installation, the  
dash mounted LED will start flashing rapidly indicating that the system is  
rearming. Opening any door will suspend the automatic arming. If the parking  
lights flashed 3 times, and the siren chirps 4 times, this indicates that the  
alarm system had been triggered in your absence. Before turning on the  
ignition key, examine the dash mounted LED's flash pattern. The number of  
flashes identifies the triggered zone. For additional information, refer to  
INTRUSION WARNING SIGNALS found later in this manual.  
INTRUSION WARNING SIGNAL:  
This system will inform you if an intrusion attempt has occurred while you  
were away from the vehicle. Upon disarm, the siren will chirp 4 times and the  
Page 4  
 
parking lights will flash 3 times. Enter the vehicle and before turning on the  
ignition switch, observe the LED flash pattern.  
If the LED flashes 2 times... pause, 2 times... pause etc., then an intrusion  
attempt was made to open the hood, trunk, or by an accessory triggering  
device. Check the vehicle for indications of forced entry to these openings.  
If the LED flashes 3 times... pause, 3 times... pause etc., then an intrusion  
attempt was made to the vehicle doors. Check all doors for indications of  
forced entry.  
If the LED flashes 4 times... pause, 4 times... pause etc., then an intrusion  
attempt was made by impact or a strong vibration that the shock sensor  
detected. Check the vehicle for possible damage to the glass or body panels.  
If the LED flashes 5 times... pause, 5 times... pause etc., then an intrusion  
attempt was made by the ignition switch.  
NOTE: The LED intrusion warning indications are stored in the system's  
memory and will be erased when the ignition switch is turned on.  
VALET SWITCH:  
The valet switch allows you to temporarily bypass all alarm functions,  
eliminating the need to hand your transmitter to parking attendants or garage  
mechanics. When the system is in valet mode, all alarm functions are  
bypassed, however the remote panic feature and remote door locks will  
remain operational.  
1. Enter the vehicle, and turn the ignition key to the ON position.  
2. Press and hold the valet push-button switch until the dash mounted LED  
turns on solid. The system will remain in the valet mode.  
3. To return to normal operation, press and release the push button switch  
any time the ignition is on.  
NOTE: Always remember to return the vehicle to the valet OFF position. This  
will ensure that the vehicle remains protected at all times.  
Page 5  
 
MANUALLYOVERRIDINGYOUR SYSTEM:  
USING THE VALET SWITCH/ MANUAL OVERRIDE  
Your system can be disarmed without the use of the keychain transmitter. This  
is necessary, since you will need the ability to operate your vehicle if the  
transmitter is lost or its battery fails. To by-pass the alarm system;  
1. Open the vehicle door. The alarm will sound.  
2. Turn the ignition key to the ON position.  
3. Within 5 seconds, press and release the valet pushbutton switch.  
The alarm system will stop sounding and enter the (by-passed) mode. You  
can now start and operate the vehicle normally.  
Typically this override mode is used only if the transmitter has become  
inoperative.  
ELIMINATING THE NORMAL ARM/DISARM CHIRPS  
You can selectively eliminate the normal arm & disarm chirps by holding the  
transmitter button slightly longer when arming or disarming. This will prevent  
the siren chirps for one arm or disarm cycle. If you find this inconvenient and  
wish to eliminate these chirps permanently, please check with your  
installation center.  
REMOTE PANIC OPERATION:  
The LOCK button on your keychain transmitter also functions as a panic  
switch for use in emergency situations. To use remote panic,  
1. Press and hold the LOCK button on the keychain transmitter for 3 or more  
seconds. The alarm will immediately sound.  
2. To stop the alarm, press and hold the LOCK button on the transmitter  
again for 3 seconds. If the button is not pressed, the alarm will  
automatically stop after 30 seconds.  
NOTE: While in the Panic mode, pressing and releasing the Lock, or the  
Unlock buttons will, if the option is installed, lock and unlock the doors  
respectively. While in the panic mode, anytime the unlock button is pressed,  
the panic feature will continue for the allotted 30 seconds, however, the  
security system will be disarmed allowing the vehicle to start.  
Page 6  
 
ADDITIONAL REMOTE FUNCTION CHANNEL 3  
The system has an optional feature, (Channel 3), that can be connected to the  
Trunk Release. To operate channel 3, press and hold the UNLOCK button of  
your keychain transmitter for four seconds.  
ANTI HI-JACK MODE OPERATION  
1. a) With the ignition switch on, and the doors closed, press and hold both  
buttons of your keychain transmitter for 1 second to initiate the anti hi-jack  
mode or open the door any time the ignition is on.  
b) If while the ignition is on, and a door is opened and then all doors are  
closed, the system will enter the anti hi-jack mode. The parking lights will turn  
on for 1.5 seconds to indicate the mode was initiated.  
2. 60 seconds after initiation, the siren will begin to sound and the parking  
lights will begin to flash.  
3. 90 seconds after initiation, the starter inhibit circuit, (if installed) will be  
activated, the siren will sound and the parking lights will flash until the  
vehicle's battery is dead, or until the system is reset.  
Note: If you are the unfortunate victim of a vehicle hi-jack, for your personal  
safety, it is best to leave the vehicle as quickly as possible. Never attempt to  
oppose the thief in any way. If the thief prevents you from leaving the vehicle,  
disarm the anti hi-jack mode to prevent the system from sounding while you  
are in the presence of your captor. Once you exit the vehicle, opening and then  
closing the door will initiate the anti hi-jack mode, and the system will go  
through the cycle mentioned above. Once the engine is turned off, it cannot be  
restarted if the optional starter inhibit circuit is installed. The system will  
continue to make noise from the siren or horn and the parking lights will  
continue to flash until the vehicle's battery is dead, or until the system is reset.  
DISARMING ANTI HI-JACK MODE  
Anytime after the anti hi-jack mode has been triggered, the circuit can be  
disarmed simply by pressing the hidden push button switch. Depressing this  
switch one time will reset the anti hi-jack mode.  
Page 7  
 
CA-110  
SYSTEM FUNCTIONS AT A GLANCE  
ALARM DASH LED INDICATORS  
RAPID FLASHING  
SLOW FLASHING  
OFF  
=
=
=
=
=
=
=
=
PASSIVEARMING  
ARMED  
DISARMED  
ON SOLID  
VALET MODE  
5 FLASH...PAUSE  
4 FLASH...PAUSE  
3 FLASH...PAUSE  
2 FLASH...PAUSE  
INTRUSION ZONE 5  
INTRUSION ZONE 4  
INTRUSION ZONE 3  
INTRUSION ZONE 2  
ALARM SIREN CHIRP INDICATION  
1 CHIRP*  
2 CHIRPS*  
3 CHIRPS  
4 CHIRPS  
=
=
=
=
ARM  
DISARMED  
ARMING WITH ENTRY POINT OPENED  
DISARM AFTER INTRUSION  
ALARM PARKING LAMP INDICATIONS  
1 FLASH  
2 FLASH  
3 FLASH  
=
=
=
ARM  
DISARM  
DISARMAFTER INTRUSION  
© 2003 Code Systems, Inc  
 
Code Systems, Inc. Limited Lifetime Warranty  
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE  
vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as  
provided below) should this Product under normal use and conditions, be proven defective in material  
or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGINALLY  
INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts  
directly related to repairs of the defect(s).  
Switches, indicator lights, and transmitter cases are similarly warranted to the original  
purchaser for a period of one (1) year from the date of purchase of the Product.  
CODE accessories, sold separately, are covered by the applicable warranty accompany-  
ing the accessory.  
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is  
removed from the vehicle in which it was originally installed; or (2) the vehicle in which the Product  
was originally installed is transferred to another party.  
This warranty does not apply to any product damaged by accident, physical or electrical  
abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other  
natural acts.  
In order for the Product to be repaired or replaced under the terms of this warranty, the  
defective Product must be returned to an authorized CODE dealer and accompanied by a copy of the  
retail sales receipt. The date of purchase and year, make and model of the vehicle in which the  
Product was originally installed must be clearly indicated on the sales receipt.  
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED  
OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE  
DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY  
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR-  
RANTY, EXPRESS OR IMPLIED, WHATSOEVER.  
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF  
CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT  
PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE  
PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION  
LABOR.  
Some states do not allow the exclusion or limitation of incidental or consequential dam-  
ages, so the above limitation may not apply to you. This warranty gives you specific legal rights and  
you may also have other rights which vary from state to state  
 
 

Cobra Electronics Automobile Alarm 8165 User Manual
Coleman Stove 5441 Series User Manual
Craftsman Lawn Mower 25949 User Manual
Craftsman Portable Generator 919670031 User Manual
Cuisinart Waffle Iron WMB 2A User Manual
Curtis Digital Photo Frame DPF151 User Manual
Delta Electronics Power Supply SIT612 User Manual
DMP Electronics Smoke Alarm P83848 User Manual
Dualit Coffeemaker CA4815 User Manual
Fortinet Safety Gate ASM S08 User Manual