CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mOUNTINg RECOmmENDaTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
faN INSTaLLaTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONTROL fEaTURES:
4 SpEED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TROUbLEShOOTINg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner’s manual completely and carefully. Retain this manual for future reference.
CAUTIon: To avoid possible electrical shock, make certain that electricity is turned
off at the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for
ceiling fan installations, if it is not, a new box must be installed. Casablanca extension poles are available for
sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The
maximum current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts.
Maximum light current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy
hatch, make sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
SAFE USE
•
•
The blades in each pack are matched for equal
weight to assure smooth fan operation. If (REmovE fUSE foR ThE
fUSE BoX
CIRCUIT yoU wIll BE
woRKIng on)
more than one fan is being installed, be careful
not to mix blades from different cartons.
Inspect the contents of your carton for possible
shipping or handling damage and report any
such damage directly to your authorized
Casablanca dealer.
18”
70”
•
•
It is always a good idea to have an assistant to
help with the installation.
84”
When cleaning, painting, or working near
your fan, be very careful of the fan and blades.
Always turn the power OFF to the ceiling fan
before servicing it, working on it, or replacing
light bulbs.
CIRCUIT BREAKER
(TRIp BREAKER foR ThE
CIRCUIT yoU wIll BE
woRKIng on)
•
Never insert anything into the path of the fan
blades while the fan is in operation.
•
•
Never install a fan over a pool or spa.
Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company
by calling toll free 1-888-227-2178, or contact
your local authorized Casablanca dealer for
assistance in obtaining service.
pN 6643040 aT1108
1
®
Pa n a m a Ha l o
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts
listed here. Before discarding packaging material, be certain that all parts have been removed.
GETTING STARTED
Carton Contents
The fan carton contains the fan body, warranty card, owner’s manual, and all the parts neccessary ( except blades) to assemble and install
your Casablanca ceiling fan. These parts are shown at the start of each installation section. before you start, go through thie Owner’s manulas
and confirm thaat you have all the parts shown in each section. Be Sure to use only genuine Casablanca blades, The blade shrink wrap holds 5
blades of matched weight. If more than one fan is being installed, be sure not to mix blade sets
Caution: When removing the shrink wrap, be careful not to scratch the blades.
perma•lock™ hardware
ALLEN SET
SCREW
DOWNROD & BALL
ASSEMBLy
3mm
ALLEN WRENCH
1¦4-20 x 1¦4”
(pRE-INSTALLED)
FAN PREPARATION
important safety information!
bEfOrE STArTIng THE InSTALLATIOn Of YOur CEILIng fAn,
InSTALL THE THrEADED DOwnrOD InTO THE mOTOr COuPLIng
AnD LOCK THE ASSEmbLY
MOTOR
WIRES
GROUND
WIRE
DOWNROD
& BALL
ASSEMBLy
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
TApERED
THREAD
Tip: The downrod has a tapered thread that is de-
signed to lock completely when correctly installed.
ALLEN
SET SCREW
Step B. Using the provided allen wrench, loosen the set
screw several turns to allow installation of the downrod.
Thread the downrod into the motor coupling until it stops
turning, this will take at least four and a half full turns.
Step C. Securely tighten the set screw with the provided
allen wrench to ensure safe operation of your fan.
mOTOR
COUpLINg
CAUTION: Failure to fully lock in the down-
rod before securely tightening the set screw
may cause the fan to separate from the
downrod during normal operation!
CEILING hARDWARE
AddITIonAl hARdwARE
21/4” x 8-32 ROUND
HEAD SCREWS (2)
FLAT WASHER
(2)
CROSSBAR
MOUNTING
BRACKET
WIRE NUT (4)
1” x 8-32 ROUND
HEAD SCREWS (2)
SUPPORT INSTALLATION
LAG SCREW
3/8”7 x 5”
LARGE FLAT
WASHER 3/8”
3
crossbar mounting bracket installation
JOIST
note: After removing the old fixture, check the outlet
box to insure that it is supported by a joist or beam
across its upper surface. If not, a 2” x 4” stud must
be installed.
Step 1. Remove the knockout plug in the center of the
outlet box or drill a 1/2” hole for the lag screw to pass
through. Then drill a 1/4” guide hole into the joist or beam
CEILING
WIRING
to a depth of 3”.
CEILING FAN
AppROVED
WIRING BOx
Step 2.Route the outlet box wires through the keyhole
slot of the crossbar mounting bracket as shown. Attach the
crossbar mounting bracket to outlet box with screws pro-
vided, assuring that the outlet box wires are not pinched
by the washer.
RIDGE SIDE
DOWN
CrOSSbAr
mOunTIng
brACKET
CAUTION: To reduce the risk of personal
injury, use only the mounting hardware pro-
vided with the approved outlet box to install
the crossbar mounting bracket.
GREEN GROUND
WIRE
FLAT
WASHER
AppROVED OUTLET
BOx HARDWARE
WARNING!
SUppORT DIRECTLy TO
BUILDING STRUCTURE ONLy.
LAG SCREW INSTALLATION
Step 3. With the large washer attached, pass the lag
screw through the center hole of the crosbar mounting
bracket and screw into guide hole. Tighten until outlet
box is firmly mounted to beam. This box must be firmly
secured to the ceiling. We recommend that the ceiling
fixture outlet box be of sufficient capacity enabling it
to support the weight of fan and light fixture under any
conditions.
LAG
SCREW
LARGE
WASHER
CANOPY hARDWARE
CANOpy SCREW (4)
CANOpy
CANOpy LOCK WASHER
HATCH
(4)
CANOpy
4
|