2-Channel Amplier Owners Manual
GT-275
GT-2125
GT-2200
GT-2300
Parts List
Included Hardware:
GT-275
GT-2125 GT-2200 GT-2300
Installation Manual
Female Quick-Connect Terminal
(for remote turn-on input)
2mm Hex Wrench
1
1
1
1
1
1
1
1
1
1
4
1
1
4
1
1
4
1
1
6
3mm Hex Wrench
Mounting Screws
Specifications
Technical Specifications:
GT-275
GT-2125 GT-2200 GT-2300
Rated Power (CEA-2006-A):
@ 4-Ohm (Stereo):
@ 2-Ohm (Stereo)
@ 4-Ohm (Mono)
75 Watts x 2
120 Watts x 2
225 Watts x 1
300 Watts x 1
125 Watts x 2
200 Watts x 2
400 Watts x 1
600 Watts x 1
200 Watts x 2
350 Watts x 2
700 Watts x 1
900 Watts x 1
300 Watts x 2
500 Watts x 2
1000 Watts x 1
1400 Watts x 1
@ 2-Ohm (Mono)
Rated Power (12v):
@ 4-Ohm (Stereo):
@ 2-Ohm (Mono)
55 Watts x 2
230 Watts x 1
95 Watts x 2
475 Watts x 1
160 Watts x 2
750 Watts x 1
260 Watts x 2
1175 Watts x 1
Frequency Response (-3dB):
Signal-to-Noise Ratio (A Weighted):
THD+N:
10Hz–95kHz
>100dB
0.03
10Hz–95kHz
>100dB
0.03
10Hz–95kHz
>100dB
0.03
10Hz–95kHz
>100dB
0.03
HighPass Crossover:
Frequency Range:
Slope (dB Per Octave):
20Hz - 350Hz 20Hz - 350Hz 20Hz - 350Hz 20Hz - 350Hz
12dB 12dB 12dB 12dB
LowPass Crossover:
Frequency Range:
Slope (dB Per Octave):
50Hz - 350Hz 50Hz - 350Hz 50Hz - 350Hz 50Hz - 350Hz
12dB or 24dB 12dB or 24db 12dB or 24db 12dB or 24db
Signal Voltage Input Range:
Fuse Amp Rating:
200mv - 8v
30 Amp
200mv - 8v
40 Amp
200mv - 8v
70 Amp
200mv - 8v
100 Amp
Dimensions:
Width:
Height:
3
1
3
1
8 ⁄4” (223mm)
13 ⁄4” (337mm) 18 ⁄4” (477mm) 22 ⁄4” (566mm)
3
3
3
3
2 ⁄8” (61mm)
2 ⁄8” (61mm)
2 ⁄8” (61mm)
2 ⁄8” (61mm)
Depth:
9” (229mm)
9” (229mm)
9” (229mm)
9” (229mm)
3
Connections
GT-2300
1
2
3
4
5
6
GT-2200
GT-2125
1
2
3
4
5 6
GT-275
1
2
4
5 6
1
2
3
4
5 6
u Stereo RCA Input
v Remote Turn-On (female spade connector supplied)
w Remote Gain Port (refer to GT-RSL manual for installation instruction)
x Left/Right/Mono Speaker Outputs (12-gauge accepted)
y 12v Power Input (4-gauge accepted)
z Ground Wire Input (4-gauge accepted)
Top Panel Removal / Installation
The cover panel is secured with two (2) 3mm screws. Once unscrewed, pull panel forward,
once clear of the corners of the end panels, it will lift off. Reverse to reinstall.
4
Controls
GT-2300
10
1
2
3
4
5 6 7 8 9
GT-2200
10
1
2
3
4
5 6 7 8 9
GT-2125
GT-275
10
1 4 5 6 7 8
9
1
2
3
5 6 7 8 9 10
4
u Stereo/Mono Switch
v Remote Gain OFF/ON Switch (ON when using GT-RSL)
w Lowpass Slope Switch (12dB Stereo, 12dB Mono, or 24dB Mono)
x Lowpass Crossover OFF/ON Switch (OFF/12dB/24dB on GT-275)
y Lowpass Frequency Adjustment (50Hz to 350Hz - continuously variable)
z Input Sensitivity (250mv to 8.0v - continuously variable)
{ Highpass Crossover OFF/ON Switch
™
| Highpass Crossover Q-Tune Adjustment (0.707 to 1.6 - continuously variable)
} Highpass Frequency Adjustment (20Hz to 350Hz - continuously variable)
~ Fuse (replace with same value mini ANL only, refer to specifications on page 3)
Status LEDs
Red
Orange
The Boston Logo will illuminate “Red” under normal operating conditions.
The Orange LED (not visible unless lit) will illuminate during start-up and under fault conditions. If this
is illuminated after start-up, please refer to troubleshooting on page 12.
5
Installation - General
WARNING! Before driving the amplifier mounting screws through any surface, be sure of what is behind that
surface. Check for the gas tank, brake lines, and any vehicle wiring harness. Never run wires outside or under
the vehicle or where they could become broken or interfere with the safe operation of the vehicle.
Before You Install
Before you install the unit, disconnect the negative (–) battery cable in the engine compartment of the vehicle.
Doing so will prevent damage to both the electrical system of the vehicle and the amplifier during installation.
Battery and Charging System
In order for the amplifier to function correctly, the electrical system of the vehicle should be professionally
checked for overall electrical capacity. When used, the amplifier will increase the demand on the battery and
alternator. Therefore, both should be thoroughly evaluated before installing the amplifier to ensure they are in
normal operating condition and able to handle the increased demand the amplifier will present to the vehicle’s
electrical system.
Wire Routing
Do not run the power wire near any low-level signals or audio cables such as the RCAs from the head unit.
Noise can be introduced into the amplifier when this occurs. It is helpful to diagram the wire layout first
before any installation is initiated.
Choose the Mounting Location
Plan your installation so that the amplifier is mounted where adequate ventilation is available. Never mount
an amplifier in the engine compartment of a vehicle!
WARNING! Before driving the mounting screws through any surface, be sure of what lies behind that
surface. Check for gas tank, brake lines, and any vehicle wiring harness.
Passenger and Trunk Compartment Mounting
If the amplifier is mounted under a seat, be sure that the vents do not become blocked. Do not allow seat
padding or other obstructive material to press down on the amplifier.
®
All Boston GT amplifiers have top panel controls. If the amplifier is mounted under a seat, position the
amplifier so the cover panel can be removed with the seat forward or back to allow adjustment of the audio
settings.
When mounting in a trunk, choose a location that will be protected from sliding cargo or other materials. Mount
the amplifier to solid surfaces only. Do not mount to plastic trim panels. Do not mount the amplifier with Velcro,
double-stick tape, or by wedging into position. Amplifier should be mounted using the movable mounting feet
and the provided mounting screws.
Multi-Position Mounting Feet
The mounting feet are designed to slide in both directions to clear installation obstructions on the mounting
surface.
Vents (Side and Rear)
The cooling vents must be kept clear of obstructions once the amplifier is installed. If the vents are obstructed,
this could lead to premature thermal shutdown or amplifier failure.
6
Installation - Wiring
Amplifier Fuses
Although the amplifier has an internal fuse, additional fuse protection should be installed as close as possible
to the battery on the positive (+) power wire going to the amplifier. An inline fuse should be installed at no
more than 18" (46cm) on the positive (+) power wire. The rating of the inline fuse should equal the value of
the internal fuse of the amplifier if only the single amplifier is connected to this wire. If other devices are con-
nected to this wire, the fuse value should be of sufficient capacity to handle the demand.
Wire Gauge
The amplifier accepts up to 4-gauge stripped wire at the DC power and ground input terminals, and 4-gauge is
recommended. Wire runs should be kept to the minimum practical length.
Power 12v and Ground (GND) Connection
5
Strip approximately ⁄8" (16mm) of insulation. The positive (+) power wire is installed into the amplifier terminal
marked “12v”. The negative (–) wire is installed into the terminal marked “GND”. The ground wire should be
as short as possible and connected directly to the chassis of the vehicle. Make sure that the chassis
connection point is free of rust, grease, dirt, paint, and other materials that may insulate the ground wire from
making proper connection. Tighten the 12v and GND terminals with the supplied 3mm hex wrench to secure
the wire into the terminals. If the power wire must be routed through a drilled or existing hole, use a nylon
panel grommet to prevent the insulation from fraying. Failure to do so could lead to an electrical short if the
wire insulation is worn through and the power wire is shorted to ground.
Remote Input Connection
Use the supplied FEMALE quick-connect terminal to connect the REMOTE trigger lead from the head unit to
the amplifier. Crimp connector to wire from head unit that controls remote turn-on (refer to head unit owner’s
manual). Once the quick-connect terminal is crimped into place, carefully push connector onto recessed MALE
REMOTE terminal adjacent to the RCA input pair (refer to the diagram on page 4).
Speaker Output Connection
5
Prepare each wire by stripping approximately ⁄8" (16mm) of insulation. The positive (+) speaker wires are
installed into the amplifier terminals marked “SPEAKER OUTPUT” / “+” (refer to the diagram on page 4). The
negative (–) speaker wires are installed into the amplifier terminals marked “SPEAKER OUTPUT” / “-”. Tighten
the “SPEAKER OUTPUT”, “+”, and “-” terminals with the supplied 2mm hex wrench to secure the wires into
the terminals. If the speaker wires must be routed through a drilled or existing hole, use a nylon panel
grommet to prevent fraying the wire insulation. Failure to do so could lead to an electrical short if the wire
insulation is worn through and the speaker wires are shorted to ground.
Mono Subwoofer Operation
When the amplifier is configured for mono operation, use the speaker output terminals marked for mono use
(refer to the diagram on page 4).
WARNING! Subwoofer impedance must not fall below 2 ohms when in MONO mode.
7
Tuning The Amplifier - Front or Rear Speakers
1) Music
The material chosen for head unit/amplifier system setup must be both clear in recording quality and dynamic in
amplitude. Many audiophile “test” discs have musical tracks with both of these characteristics and should be used.
2) Input Sensitivity Control
Turn control all the way counterclockwise (minimum position). In this position, the amplifier will be less sensitive to
the input signal from the head unit (refer to the diagram on page 5).
3) Highpass & Lowpass Crossover Controls
Crossovers should be turned “OFF” during this phase of setup . Move the HIGHPASS and LOWPASS switches to the
“OFF” position (refer to the diagram on page 5), with these settings, full-range signal is sent to the speaker
outputs. If over-excursion is detected from speakers, move HIGHPASS switch to “ON” and slowly rotate clockwise
until over-excursion is eliminated.
4) Head Unit
The head unit should have all controls such as bass, treble, balance, and fader set to the flat or centered position.
The volume control should be at the minimum setting. If the head unit has any equalization or bass management
features such as boost, they should be defeated at this time. Turn head unit on, and verify that the RED status LED
(logo) is illuminated on the amplifier.
5) Volume
With the chosen musical track playing, turn the head unit volume control up until the maximum level of
undistorted signal is heard from the speakers. (For most head units, this will be near the end of the volume
control range.)
WARNING! A distorted signal from the head unit sent to the amplifier can cause loudspeaker failure at higher
listening levels.
2-Channel Highpass Operation Switch Configuration Diagram
8
Tuning The Amplifier - Front or Rear Speakers
6) Input Sensitivity Control
Slowly rotate the control clockwise (refer to the diagram on page 5) until maximum undistorted playing level is
heard from the speakers. Listen closely for bottoming from the speakers. If detected, rotate the input sensitivity
control counterclockwise until it is eliminated.
7) Crossover Controls
To achieve higher undistorted playing levels from the main speakers, the highpass crossover must be engaged.
Rotate the crossover control fully clockwise (refer to the diagram on page 5). The highpass crossover point is now
™
set at 350Hz. Rotate “Q-Tune ” Control fully counterclockwise. Move crossover switch to the right (ON) position.
Slowly rotate the input sensitivity control clockwise until maximum undistorted playing level is heard from the
speakers. Listen closely for bottoming from the speakers. If detected, rotate the input sensitivity control counterclock-
wise until it is eliminated. Slowly rotate the highpass crossover control counterclockwise while listening for
bottoming. You are lowering the crossover point, which means that more bass signal is being sent to the speakers. If
bottoming is detected, rotate the input sensitivity control counterclockwise until it is eliminated and/or rotate the
Highpass crossover control clockwise to raise the crossover point.
™
8) Q-Tune Control
™
Once the highpass crossover point has been determined, use the Q-Tune control (refer to the diagram on page 5)
to increase the bass information centered around the crossover point.
™
Setting the Q-Tune control is done in conjunction with setting the levels on the input sensitivity and highpass
™
crossover frequency controls. You may find while setting the Q-Tune that over-excursion may be detected in the
™
front speakers; lowering the Q-Tune input sensitivity or raising the highpass crossover point will eliminate this.
Minor adjustments to each setting are required to fine-tune the system.
™
™
Setting the Q-Tune is a subtle process. It is recommended that the Q-Tune setting be left in the 0.7 position and
adjusted only after the input sensitivity and highpass crossover ranges are known. Small adjustments to the Q-Tune
setting are all that are required to fine-tune the system.
™
fuse
2-Channel Operation Wiring Configuration Diagram
9
Tuning The Amplifier - Subwoofer (s)
1) Input Switch
Move switch to the right-hand (MONO) position (refer to the diagram on page 5); the inputs are summed to
mono. Connect the subwoofer to the speaker output terminals marked for mono operation. NOTE: Subwoofer
impedance is 2 ohms minimum.
2) Head Unit
The head unit should have all controls such as bass, treble, balance, and fader set to the flat or centered
position. The volume control should be at the minimum setting. If the head unit has any equalization or bass
management features such as boost, they should be deactivated at this time. Turn head unit on, and verify that
the RED status LED (logo) is illuminated on the amplifier.
3) Volume
With the chosen musical track playing, turn the head unit volume control up until the maximum level of
undistorted signal is heard from the speakers. For most head units, this will be at the end of the volume
control range.
WARNING! A distorted signal from the head unit sent to the amplifier can cause speaker failure at higher
listening levels.
4) Input Sensitivity Control
Turn control (refer to the diagram on page 5) all the way counterclockwise (minimum position). In this
position, the amplifier will be less sensitive to the input signal from the head unit. Slowly rotate this control
clockwise until maximum undistorted playing level is heard from the subwoofer(s). Listen closely for faults
such as bottoming from the subwoofer(s). If fault is detected, rotate input sensitivity control counterclockwise
until fault is eliminated. At this point, the maximum undistorted subwoofer playing level has been defined.
™
Bridged Lowpass with Q-Tune Switch Configuration Diagram
10
Tuning The Amplifier - Subwoofer (s)
5) Lowpass Crossover Control
Move the selector switch to “ON” (refer to the diagram on page 5). In this setting, lowpass signal is sent to the
speaker outputs. Experiment with the crossover point settings while the subwoofer is active. A higher setting
will increase the perceived output, and a lower setting will make the bass response more omnidirectional. 12
or 24dB crossover slopes are available. Depending on your installation and listening preferences, one will
work more effectively.
6) Highpass Crossover Control
With some subwoofer applications, it may be necessary to use the highpass crossover to protect the subwoofer from
over-excursion. Move the selector switch to “ON” (refer to the diagram on page 5) The highpass should be set
to the tuning frequency (vented) or the FS of the subwoofer (sealed or freeair) If you are using a Boston
®
™
Acoustics subwoofer, the correct highpass frequency and Q-Tune settings for that enclosure are outlined in the
subwoofer’s owners manual.
™
7) Q-Tune Control
™
Once the highpass crossover point has been determined, use the Q-Tune control (refer to the diagram on page 5)
to increase the bass information centered around the highpass crossover point.
™
Setting the Q-Tune control is done in conjunction with setting the levels on the input sensitivity and highpass
™
crossover frequency controls. You may find while setting the Q-Tune that over-excursion may be detected in the
™
subwoofer (s); lowering the Q-Tune input sensitivity or raising the highpass crossover point will eliminate this.
Minor adjustments to each setting are required to fine-tune the system.
™
™
Setting the Q-Tune is a subtle process. It is recommended that the Q-Tune setting be left in the 0.7 position and
adjusted only after the input sensitivity and highpass crossover ranges are known. Small adjustments to the Q-Tune
setting are all that are required to fine-tune the system.
™
8) RSL Control
The remote level control (GT-RSL) gives you independent level adjustment of the subwoofer’s output level beyond
the standard system volume control. Please refer to the RSL’s manual for installation instruction. The GT-RSL is
available separately, please consult your authorized Boston Acoustics dealer.
fuse
Bridged Operation Wiring Configuration Diagram
11
Amplifier Troubleshooting Guide
Status LEDs on Amplifier not Lit—Head Unit (Source) Turned “ON”
Verify
Remote turn-on wire from source to amplifier has proper voltage
Power (B+) connections at amplifier, terminal blocks, and battery are secure
Ground (GND) connections at amplifier and vehicle chassis are secure
Battery B+ fuse and amplifier fuse are OK
B+ at battery and B+ at amplifier have proper voltage
Status LEDs Lit, no Output from Speakers—Speakers in Normal Operating Condition
Verify
High-level cables from speaker(s) to amplifier are securely connected
RCA cables from amplifier to source are securely connected
Sensitivity adjustment on amplifier is correctly adjusted
Engine Noise from Speaker(s)
Turn source “OFF” and disconnect RCA cables at amplifier
If noise stops, check equipment and cables leading to amplifier
RCA cables are of good quality with no breakage to internal shields
RCA cables from source to amplifier are not run alongside power
Verify
Amplifier Output Distorted—Music not Recorded with Intentional Distortion
Verify
Source output to amplifier is not distorted
Amplifier input sensitivity is correctly adjusted
Amplifier Shutting Down, Red Blinking and Orange LEDs Lit—Amplifier in Thermal Protection Mode
Verify
Amplifier is mounted with adequate air circulation around vents
Amplifier does not have obstructions blocking back or side panel vents
Amplifier is not mounted under carpet
Speakers meet correct impedance for application (mono or stereo hookup)
Amplifier not Turning “ON”, Orange LED Lit—Amplifier not Connected to a Shorted Speaker
Verify
Speaker crossover is not defective
High-level cables from speaker to amplifier are not shorted
Amplifier not Turning And Both LED (s) Blinking—Speakers, Crossovers, and Cable OK
Internal fuse needs to be replaced
Verify
Replace fuse with fuse of same value
Amplifier not Turning “ON”, Orange LED Lit—Speakers, Crossovers, and Cable OK
Amplifier requires service
If Service Seems Necessary
First, contact the dealer from whom you purchased the product, or contact us via e-mail at:
Europe: [email protected]
Japan: [email protected]
We will promptly advise you of what action to take.
Boston Acoustics, Inc. 300 Jubilee Drive, Peabody, MA 01960 USA
T: 978.538.5000 F: 978.538.5100 W: bostonacoustics.com
Boston, Boston GT, Boston Acoustics, and the Boston Acoustics logo are registered trademarks and DualMode and Q-Tune are trademarks of Boston Acoustics, Inc.
Specifications are subject to change without notice. © 2008 Boston Acoustics, Inc. All rights reserved. Covered by patents issued and/or pending. 142-003178-0
|