Black Decker Grinder KG2001 User Manual

Amoladora Angular  
Angle Grinder  
MANUAL DE INSTRUCCIONES  
INSTRUCTION MANUAL  
Cat. N° KG2001  
Español  
English  
4
8
Advertencia: Léase este instructivo antes de usar el producto.  
Warning: Read instruction manual before using product.  
 
 
ESPAÑOL  
 
ESPAÑOL  
 
ESPAÑOL  
 
ESPAÑOL  
/
5/8"-11/M14  
Pueden consultar la dirección de su servicio en la lista de  
Centros de Servicio en Latinoamérica incluída con esta  
herramienta o poniéndose en contacto con la oficina local  
de Black & Decker en la dirección que se indica al final de  
este manual.  
 
ENGLISH  
Intended use  
Your Black & Decker angle grinder has been designed for  
cutting metal and masonry using the appropriate type of cutting  
or grinding disc.This tool is intended for consumer use only.  
Remove adjusting keys and wrenches  
Always check that adjusting keys and wrenches are removed  
from the tool before operating the tool.  
Extension cables  
Before use, inspect the extension cable and replace if  
damaged. When using the tool outdoors, only use extension  
cables intended for outdoor use. Up to 30 m of Black & Decker  
extension cable can be used without loss of power.  
Use appropriate tool  
The intended use is described in this instruction manual. Do  
not force small tools or attachments to do the job of a heavy-  
duty tool. The tool will do the job better and safer at the rate  
for which it was intended. Do not force the tool. Do not use  
the tool for purposes not intended, for example, do not use a  
circular saw to cut tree limbs or logs.  
Safety instructions  
Warning! When using mains-powered tools, basic safety  
precautions, including the following, should always be  
followed to reduce the risk of fire, electric shock, personal  
injury and material damage.  
Read all of this manual carefully before operating the tool.  
Retain this manual for future reference.  
Remove the plug from the socket before carrying out any  
adjustment, servicing or maintenance.  
Keep work area clean  
Cluttered areas and benches can cause accidents.  
Consider work area environment  
Warning! The use of any accessory or attachment or  
performance of any operation with this tool other than those  
recommended in this instruction manual may present a risk of  
personal injury.  
Do not expose the tool to rain. Do not use the tool in damp or  
wet conditions. Keep the work area well lit. Do not use the  
tool where there is a risk of causing fire or explosion, e.g. in  
the presence of flammable liquids and gases.  
Keep children away  
Do not allow children, visitors or animals to come near the  
work area or to touch the tool or mains cable.  
Dress properly  
Do not wear loose clothing or jewellery, as these can be  
caught in moving parts. Preferably wear rubber gloves and  
non-slip footwear when working outdoors. Wear protective  
hair covering to keep long hair out of the way.  
Personal protection  
Always use safety glasses. Use a face or dust mask whenever  
the operations may produce dust or flying particles.  
Hearing protection should be worn.  
Check for damaged parts  
Before use, carefully check the tool and mains cable for  
damage. Check for misalignment and seizure of moving parts,  
breakage of parts, damage to guards and switches and any  
other conditions that may affect its operation. Ensure that the  
tool will operate properly and perform its intended function.  
Do not use the tool if any part is damaged or defective. Do not  
use the tool if the switch does not turn it on and off. Have any  
damaged or defective parts repaired or replaced by an  
authorised repair agent. Never attempt any repairs yourself.  
Unplug the tool  
Unplug the tool when it is not in use, before changing any  
parts of the tool, accessories or attachments and before  
servicing.  
Avoid unintentional starting  
Guard against electric shock  
Prevent body contact with earthed or grounded surfaces  
Do not carry the tool with a finger on the on/off switch.  
Be sure that the tool is switched off when plugging in.  
(e.g. pipes, radiators, cookers and refrigerators). Electric safety Do not abuse cord  
can be further improved by using a high-sensitivity  
(30 mA / 30 mS) residual current device (RCD).  
Do not overreach  
Never carry the tool by its cord or pull it to disconnect from the  
socket. Keep the cord away from heat, oil and sharp edges.  
Store idle tools  
Keep proper footing and balance at all times.  
Stay alert  
When not in use, tools should be stored in a dry, locked up or  
high place, out of reach of children.  
Watch what you are doing. Use common sense.  
Do not operate the tool when you are tired.  
Secure workpiece  
Use clamps or a vice to hold the workpiece. It is safer and it  
frees both hands to operate the tool.  
Connect dust extraction equipment  
If devices are provided for the connection of dust extraction  
and collection facilities, ensure that these are connected and  
properly used.  
Maintain tools with care  
Keep cutting tools sharp and clean for better and safer  
performance. Follow the instructions for maintenance and  
changing accessories. Keep handles and switches dry,  
clean and free from oil and grease.  
Repairs  
This tool complies with relevant safety requirements.  
Repairs should only be carried out by qualified persons using  
original spare parts; otherwise this may result in considerable  
danger to the user.  
 
8
ENGLISH  
Electrical safety  
This tool is double insulated; therefore no earth wire  
Beware that after switching off the tool the wheel  
continues to rotate for a short period.  
is required. Always check that the power supply  
corresponds to the voltage on the rating plate.  
Ensure that ventilation slots are kept clear when working  
in dusty conditions. If it should become necessary to clear  
dust, first disconnect the tool from the mains supply.  
Avoid damaging internal parts, use a soft brush or dry  
cloth, do not use metallic objects.  
Additional safety instructions for angle grinders  
Abrasive wheels shall be stored and handled with care in  
accordance with manufacturer’s instructions and always  
store grinding and cutting discs in a dry place.  
Read the instruction manual before use.  
Wear safety glasses or goggles when operating this  
tool.  
Features  
This tool includes some or all of the following features.  
1. On/off switch  
2. Lock-off button  
3. Side handle  
4. Spindle lock  
5. Guard  
Wear ear protection when operating this tool.  
Always use eye and ear protection when operating this  
tool.  
Personal protective equipment such as dust mask, gloves,  
helmet and apron should be worn.  
Assembly  
Do not cut or grind light metal with a magnesium content  
exceeding 80%, since this type of metal is flammable.  
Only use grinding and cutting discs and other accessories  
recommended in this manual.  
Warning! Make sure that the tool is switched off and unplugged.  
Fitting and removing the guard (fig. A)  
Make sure that the maximum speed of the grinding or  
cutting disc exceeds the no-load speed of the tool.  
Do not use grinding and cutting discs that do not conform  
to the dimensions stated in the technical data. Do not use  
separate reducing bushings or adapters or make  
unauthorised modifications to adapt large hole abrasive  
wheels.  
Fitting  
Place the tool on a table, with the spindle (6) facing up.  
Hold the guard (5) over the tool as shown.  
Align the holes in the adjusting plate (7) with the screw  
holes (8).  
Press the guard down and insert the screws (9) into the  
holes.  
Do not cut workpieces requiring a maximum depth of cut  
exceeding that of the cutting disc.  
Tighten the screws.  
Do not use cutting discs for side grinding.  
Removing  
Inspect grinding and cutting discs before each use. Do not  
use chipped, cracked or otherwise defective discs.  
Ensure that the abrasive product is correctly mounted and  
tightened before use and run the tool at no-load for 30 s  
in a safe position, stop immediately if there is considerable  
vibration or if other defects are detected. If this condition  
occurs, check the machine to determine the cause.  
Ensure that blotters are used when they are provided with  
the bonded abrasive product and when they are required.  
When applying a threaded hole disc, ensure that the  
thread is long enough to accept the spindle length.  
Never use the tool without the guard.  
Remove the screws (9).  
Take the guard off the tool.  
Warning! Never use the tool without the guard.  
Adjusting the guard (fig. B)  
The guard can be rotated 180°.  
Slacken the screws (9) and the nut (10).  
Rotate the guard as required.  
Re-tighten the screws and the nut.  
Fitting the side handle  
Check that the workpiece is properly supported.  
Do not exert side pressure on the grinding or cutting disc.  
Ensure that sparks resulting from use do not create a  
hazard e.g. do not hit persons, or ignite flammable  
substances.  
Screw the side handle (3) into one of the mounting holes  
in the tool.  
Warning! Always use the side handle.  
 
9
ENGLISH  
Maintenance  
Your tool has been designed to operate over a long period of  
time with a minimum of maintenance. Continuous satisfactory  
Fitting and removing grinding or cutting discs (fig. C - F)  
Always use the correct type of disc for your application.  
Always use discs with the correct diameter and bore size  
(see technical data). The maximum thickness for grinding discs operation depends upon proper tool care and regular cleaning.  
is 6 mm, for cutting discs 3.5 mm.  
Regularly clean the ventilation slots in your tool using a  
Fitting  
Fit the guard as described above.  
soft brush or dry cloth.  
Regularly clean the motor housing using a damp cloth.  
Do not use any abrasive or solvent-based cleaner.  
Place the inner flange (11) onto the spindle (6) as shown  
(fig. C). Make sure that the flange is correctly located on  
the flat sides of the spindle.  
Place the disc (12) onto the spindle (6) as shown (fig. D).  
If the disc has a raised centre (13), make sure that the  
raised centre faces the inner flange.  
Make sure that the disc locates correctly on the inner flange.  
Place the outer flange (14) onto the spindle. When fitting  
a grinding disc, the raised centre on the outer flange must  
face towards the disc (A in fig. E). When fitting a cutting  
disc, the raised centre on the outer flange must face away  
from the disc (B in fig. E).  
Technical data  
KG2001  
120/220  
2,000  
8,400  
180  
Voltage  
VAC  
W
Power input  
No-load speed  
Disc diameter  
Disc bore  
Spindle size  
Weight  
min-1  
mm  
mm  
22  
5/8"-11/M14  
7
kg  
Service  
Keep the spindle lock (4) depressed and tighten the outer  
flange using the two-pin spanner (15) (fig. F).  
Removing  
You can check the location of your nearest authorized service  
center by contacting your local Black & Decker office at the  
address indicated in this manual.  
Keep the spindle lock (4) depressed and loosen the outer  
flange (14) using the two-pin spanner (15) (fig. F).  
Remove the outer flange (14) and the disc (12).  
Use  
Warning! Let the tool work at its own pace.  
Do not overload.  
Carefully guide the cable in order to avoid accidentally  
cutting it.  
Be prepared for a stream of sparks when the grinding or  
cutting disc touches the workpiece.  
Always position the tool in such a way that the guard  
provides optimum protection from the grinding or cutting  
disc.  
Switching on and off  
To switch the tool on, press the lock-off button (2) and  
subsequently press the on/off switch (1).  
To switch the tool off, release the on/off switch (1).  
Warning! Do not switch the tool off while under load.  
Hints for optimum use  
Firmly hold the tool with one hand around the side handle  
and the other hand around the main handle.  
When grinding, always maintain an angle of approx. 15°  
between the disc and the workpiece surface.  
 
10  
ENGLISH  
Solamente para propósito de Argentina:  
Importado por: Black & Decker Argentina S.A.  
Pacheco Trade Center  
Colectora Este de Ruta Panamericana  
Km. 32.0 El Talar de Pacheco  
Partido de Tigre  
Buenos Aires (B1618FBQ)  
República de Argentina  
No. de Importador: 1146/66  
Tel. (011) 4726-4400  
Imported by/Importado por:  
Black & Decker do Brasil Ltda.  
Rod. BR 050, s/n° - Km 167  
Dist. Industrial II  
Uberaba ˆ MG ˆ Cep: 38064-750  
CNPJ: 53.296.273/0001-91  
Insc. Est.: 701.948.711.00-98  
S.A.C.: 0800-703-4644  
Solamente para propósitos de CCA  
Importado por: Black & Decker LLC  
Calle Miguel Brostella Final  
Edificio Milano I, Mezanine 5,6 y 7  
El Dorado, Panama  
Tel. 507-360.5700  
Solamente para propósitos de Colombia  
Importado por: Black & Decker de Colombia, S.A.  
Carrera 85D # 51-65, Bodega 23  
Complejo Logístico San Cayetano  
Bogota - Colombia  
Tel. 744-7100  
Solamente para propósito de Chile:  
Importado por: Black & Decker de Chile, S.A.  
Av. Pdte. Eduardo Frei M. 6001-67 Conchalí  
Santiago de Chile  
Tel. (56-2) 687 1700  
Solamente para propósito de México:  
Importado por: Black & Decker S.A. de C.V.  
Bosques de Cidros, Acceso Radiatas No.42  
3a. Sección de Bosques de las Lomas  
Delegación Cuajimalpa,  
05120, México, D.F.  
Tel. (52) 555-326-7100  
R.F.C.: BDE810626-1W7  
Black & Decker del Perú S.A.  
Av. Enrique Meiggs 227.  
Pque. Industrial - Callao  
Teléfono: (511) 452-5577  
RUC 20266596805  
Impreso en China  
Printed in China  
09/04/07  
478307-00  
 
11  

Black Box Network Cables AC455A TX R2 User Manual
Blanco Indoor Furnishings 513 685 User Manual
Bosch Appliances Network Router ATM POS Bridge User Manual
Bose DVD Player 135 User Manual
Bose DVD Player AM193147_03_V User Manual
Briggs Stratton Portable Generator 30218 User Manual
Carrier Furnace 58SX040 IBC User Manual
Carrier Heat Pump 50NQ User Manual
Chauvet Indoor Furnishings CHAOVET User Manual
Christie Digital Systems Projector LW400 User Manual