Behringer Music Mixer PMP518M User Manual

User Manual  
EUROPOWER PMP518M  
Ultra-Compact 180-Watt 5-Channel Powered Mixer with  
Multi-FX Processor and FBQ Feedback Detection System  
behringer.com  
 
3
EUROPOWER PMP518M User Manual  
9. Do not defeat the safety purpose of the polarized  
or grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding-type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety. If the  
provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
Limited Warranty  
§ 1 Warranty  
[1] This limited warranty is valid only if you purchased  
the product from a BEHRINGER authorized dealer in the  
country of purchase. A list of authorized dealers can be  
found on BEHRINGER’s website behringer.com under  
“Where to Buy, or you can contact the BEHRINGER office  
closest to you.  
Important Safety  
Instructions  
10. Protect the power cord from being walked on or  
pinched particularly at plugs, convenience receptacles,  
and the point where they exit from the apparatus.  
Terminals marked with this symbol carry  
electrical current of sufficient magnitude to  
constitute risk of electric shock. Use only  
[2] MUSIC Group* warrants the mechanical and  
electronic components of this product to be free of defects  
in material and workmanship if used under normal  
operating conditions for a period of one (1) year from  
the original date of purchase (see the Limited Warranty  
11. Use only attachments/accessories specified by  
the manufacturer.  
high-quality commercially-available speaker cables with  
1" TS plugs pre-installed. All other installation or  
modification should be performed only by  
qualified personnel.  
12. Use only with the  
cart, stand, tripod, bracket, terms in § 4 below), unless a longer minimum warranty  
or table specified by the period is mandated by applicable local laws. If the product  
manufacturer, or sold with shows any defects within the specified warranty period  
the apparatus. When a cart and that defect is not excluded under § 4, MUSIC Group  
is used, use caution when shall, at its discretion, either replace or repair the product  
moving the cart/apparatus using suitable new or reconditioned product or parts.  
This symbol, wherever it appears, alerts you  
to the presence of uninsulated dangerous  
voltage inside the enclosure - voltage that  
may be sufficient to constitute a risk of shock.  
combination to avoid  
In case MUSIC Group decides to replace the entire product,  
this limited warranty shall apply to the replacement  
product for the remaining initial warranty period, i.e.,  
one (1) year (or otherwise applicable minimum warranty  
period) from the date of purchase of the original product.  
This symbol, wherever it appears, alerts you injury from tip-over.  
to important operating and maintenance  
instructions in the accompanying literature.  
Please read the manual.  
13. Unplug this apparatus during lightning storms or  
when unused for long periods of time.  
14. Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power supply cord or plug  
is damaged, liquid has been spilled or objects have fallen  
into the apparatus, the apparatus has been exposed  
to rain or moisture, does not operate normally, or has  
been dropped.  
[3] Upon validation of the warranty claim, the repaired  
or replacement product will be returned to the user freight  
prepaid by MUSIC Group.  
Caution  
To reduce the risk of electric shock, do not  
remove the top cover (or the rear section).  
No user serviceable parts inside. Refer servicing to  
qualified personnel.  
[4] Warranty claims other than those indicated above  
are expressly excluded.  
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF  
OF PURCHASE COVERING YOUR LIMITED WARRANTY.  
THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF  
OF PURCHASE.  
Caution  
15. The apparatus shall be connected to a MAINS socket  
outlet with a protective earthing connection.  
To reduce the risk of fire or electric shock,  
do not expose this appliance to rain and  
moisture. The apparatus shall not be exposed to dripping  
16. Where the MAINS plug or an appliance coupler is  
or splashing liquids and no objects filled with liquids, such used as the disconnect device, the disconnect device shall  
§ 2 Online registration  
as vases, shall be placed on the apparatus.  
remain readily operable.  
Please do remember to register your new BEHRINGER  
equipment right after your purchase at behringer.com  
under“Support”and kindly read the terms and conditions  
of our limited warranty carefully. Registering your  
purchase and equipment with us helps us process  
your repair claims quicker and more efficiently.  
Thank you for your cooperation!  
Caution  
These service instructions are for use  
by qualified service personnel only.  
To reduce the risk of electric shock do not perform any  
servicing other than that contained in the operation  
instructions. Repairs have to be performed by qualified  
service personnel.  
§ 3 Return materials authorization  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
[1] To obtain warranty service, please contact the  
retailer from whom the equipment was purchased.  
Should your BEHRINGER dealer not be located in your  
vicinity, you may contact the BEHRINGER distributor for  
your country listed under“Support”at behringer.com.  
If your country is not listed, please check if your problem  
can be dealt with by our“Online Support”which may  
also be found under“Support”at behringer.com.  
Alternatively, please submit an online warranty claim at  
behringer.com BEFORE returning the product. All inquiries  
must be accompanied by a description of the problem  
and the serial number of the product. After verifying  
the product’s warranty eligibility with the original sales  
receipt, MUSIC Group will then issue a Return Materials  
Authorization (“RMA”) number.  
Legal Disclaimer  
Technical specifications and appearance are subject to change without  
notice. The information contained herein is correct at the time of printing.  
All trademarks are the property of their respective owners. MUSIC Group  
accepts no liability for any loss which may be suffered by any person  
who relies either wholly or in part upon any description, photograph or  
statement contained herein. Colors and specifications may vary slightly from  
product. BEHRINGER products are sold through authorized dealers only.  
Distributors and dealers are not agents of MUSIC Group and have absolutely  
no authority to bind MUSIC Group by any express or implied undertaking  
or representation. This manual is copyrighted. No part of this manual may  
be reproduced or transmitted in any form or by any means, electronic or  
mechanical, including photocopying and recording of any kind, for any  
purpose, without the express written permission of Red Chip Company Ltd.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as  
radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
ALL RIGHTS RESERVED.  
© 2010 Red Chip Company Ltd.  
Trident Chambers, Wickhams Cay, P.O. Box 146,  
Road Town, Tortola, British Virgin Islands  
behringer.com  
 
 
4
EUROPOWER PMP518M User Manual  
[2] Subsequently, the product must be returned in  
its original shipping carton, together with the return  
authorization number to the address indicated by  
MUSIC Group.  
§ 9 Amendment  
[7] Any repair or opening of the unit carried out by  
unauthorized personnel (user included) will void the  
limited warranty.  
Warranty service conditions are subject to change without  
notice. For the latest warranty terms and conditions  
and additional information regarding MUSIC Group’s  
limited warranty, please see complete details online at  
behringer.com.  
[8] If an inspection of the product by MUSIC Group  
shows that the defect in question is not covered by the  
limited warranty, the inspection costs are payable by  
the customer.  
[3] Shipments without freight prepaid will not  
be accepted.  
* MUSIC Group Macao Commercial Offshore Limited of  
Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,  
including all MUSIC Group companies  
§ 4 Warranty Exclusions  
[9] Products which do not meet the terms of this  
limited warranty will be repaired exclusively at the buyer’s  
expense. MUSIC Group or its authorized service center will  
inform the buyer of any such circumstance. If the buyer  
fails to submit a written repair order within 6 weeks after  
notification, MUSIC Group will return the unit C.O.D. with  
a separate invoice for freight and packing. Such costs will  
also be invoiced separately when the buyer has sent in a  
written repair order.  
[1] This limited warranty does not cover consumable  
parts including, but not limited to, fuses and batteries.  
Where applicable, MUSIC Group warrants the valves or  
meters contained in the product to be free from defects in  
material and workmanship for a period of ninety (90) days  
from date of purchase.  
[2] This limited warranty does not cover the product  
if it has been electronically or mechanically modified  
in any way. If the product needs to be modified or  
adapted in order to comply with applicable technical  
or safety standards on a national or local level, in any  
country which is not the country for which the product  
was originally developed and manufactured, this  
modification/adaptation shall not be considered a defect  
in materials or workmanship. This limited warranty does  
not cover any such modification/adaptation, regardless  
of whether it was carried out properly or not. Under the  
terms of this limited warranty, MUSIC Group shall not  
be held responsible for any cost resulting from such a  
modification/adaptation.  
[10] Authorized BEHRINGER dealers do not sell new  
products directly in online auctions. Purchases made  
through an online auction are on a“buyer beware”basis.  
Online auction confirmations or sales receipts are not  
accepted for warranty verification and MUSIC Group will  
not repair or replace any product purchased through an  
online auction.  
§ 5 Warranty transferability  
This limited warranty is extended exclusively to the  
original buyer (customer of authorized retail dealer) and  
is not transferable to anyone who may subsequently  
purchase this product. No other person (retail dealer, etc.)  
shall be entitled to give any warranty promise on behalf  
of MUSIC Group.  
[3] This limited warranty covers only the product  
hardware. It does not cover technical assistance for  
hardware or software usage and it does not cover  
any software products whether or not contained in  
the product. Any such software is provided“AS IS”  
unless expressly provided for in any enclosed software  
limited warranty.  
§ 6 Claim for damage  
Subject only to the operation of mandatory applicable  
local laws, MUSIC Group shall have no liability to the buyer  
under this warranty for any consequential or indirect  
loss or damage of any kind. In no event shall the liability  
of MUSIC Group under this limited warranty exceed the  
invoiced value of the product.  
[4] This limited warranty is invalid if the factory-  
applied serial number has been altered or removed from  
the product.  
[5] Free inspections and maintenance/repair work  
are expressly excluded from this limited warranty, in  
particular, if caused by improper handling of the product  
by the user. This also applies to defects caused by normal  
wear and tear, in particular, of faders, crossfaders,  
potentiometers, keys/buttons, guitar strings, illuminants  
and similar parts.  
§ 7 Limitation of liability  
This limited warranty is the complete and exclusive  
warranty between you and MUSIC Group. It supersedes  
all other written or oral communications related to this  
product. MUSIC Group provides no other warranties for  
this product.  
[6] Damage/defects caused by the following conditions  
are not covered by this limited warranty:  
§ 8 Other warranty rights and  
national law  
[1] This limited warranty does not exclude or limit the  
improper handling, neglect or failure to operate the  
unit in compliance with the instructions given in  
BEHRINGER user or service manuals;  
buyer’s statutory rights as a consumer in any way.  
[2] The limited warranty regulations mentioned herein  
are applicable unless they constitute an infringement of  
applicable mandatory local laws.  
connection or operation of the unit in any way  
that does not comply with the technical or safety  
regulations applicable in the country where the  
product is used;  
[3] This warranty does not detract from the seller’s  
obligations in regard to any lack of conformity of the  
product and any hidden defect.  
damage/defects caused by acts of God/Nature  
(accident, fire, flood, etc) or any other condition that  
is beyond the control of MUSIC Group.  
behringer.com  
 
5
EUROPOWER PMP518M User Manual  
1. Introduction  
1.1.3 Online registration  
Right from the very start it has been our goal to design a revolutionary unit that  
can be used for a wide variety of applications. And indeed, this overwhelming  
power mixer gives you plenty of functionality and a broad range of connection  
and expansion options.  
Please register your new BEHRINGER equipment right after your purchase  
warranty carefully.  
Should your BEHRINGER product malfunction, it is our intention to have it  
repaired as quickly as possible. To arrange for warranty service, please contact  
the BEHRINGER retailer from whom the equipment was purchased. Should your  
BEHRINGER dealer not be located in your vicinity, you may directly contact  
one of our subsidiaries. Corresponding contact information is included in the  
original equipment packaging (Global Contact Information/European Contact  
Information). Should your country not be listed, please contact the distributor  
nearest you. A list of distributors can be found in the support area of our website  
(http://behringer.com).  
1.1 Before you get started  
1.1.1 Shipment  
Your EUROPOWER was carefully packed at the factory and the packaging is  
designed to protect the unit from rough handling. Nevertheless, we recommend  
that you carefully examine the packaging and its contents for any signs of  
physical damage which may have occurred during transit.  
If the unit is damaged, please do NOT return it to BEHRINGER,  
but notify your dealer and the shipping company immediately.  
Otherwise, claims for damage or replacement may not be granted.  
Registering your purchase and equipment with us helps us process your repair  
claims more quickly and efficiently.  
Thank you for your cooperation!  
We recommend that you use a flight case, so as to give your power  
mixer optimum protection during use or transport.  
Always use the original packing carton to prevent damage during  
storage or transport.  
Make sure that children cannot play unsupervised with the device  
or its packaging.  
Please ensure proper disposal of all packing materials.  
1.1.2 Initial operation  
Be sure that there is enough air space around the unit for cooling and, to avoid  
overheating, please do not place the EUROPOWER near radiators, etc.  
Blown fuses must be replaced by fuses of the same type and rating!  
Please refer to the “Specifications” for details.  
The mains connection is made using the enclosed power cord and a standard IEC  
receptacle. It meets all of the international safety certification requirements.  
Please make sure that all units have proper ground connection.  
For your own safety, never remove or disable the ground conductor  
from the unit or on the AC power cord.  
The sound quality may diminish within the range of powerful  
broadcasting stations and high-frequency sources. Increase the  
distance between the transmitter and the device and use shielded  
cables for all connections.  
behringer.com  
 
 
6
EUROPOWER PMP518M User Manual  
2. Control Elements  
[1] [3] [4]  
[12] [9] [10] [11]  
[13]  
[17]  
[2]  
[5]  
[8]  
[7] [6]  
Fig. 2.1: Front panel control elements and connectors  
2.1 Input channels  
[19] [20] [21] [14] [16] [15] [18]  
[22]  
2.3 Main section  
[1] The HIGH control in the EQ section governs the high-frequency range of the [13] Your power mixer is equipped with a graphic 7-band equalizer.  
respective channel.  
Use the EQ to adjust the sound to the room acoustics.  
[2] The LOW control allows you too boost/cut the low-frequency range.  
[14] Press the FBQ IN switch to activate the FBQ Feedback Detection System.  
The frequencies causing feedback are shown by the brightly lit fader LEDs.  
Simply lower the level of the respective frequency range until feedback  
disappears and the LED goes out.  
[3] The FX control determines the signal level sent from each channel to the  
built-in effects processor.  
Please note that the effects processor signal will be inaudible when the  
FX LEVEL control ([15]) is set fully counter-clockwise.  
[15] Turn the FX LEVEL control to add effect to the main mix. When it is fully  
counterclockwise, no effect signal is added.  
[4] The LEVEL control adjusts the channel signal level in the main mix.  
[16] The CD/tAPE IN control adjusts the volume of the CD/TAPE IN signal (see [19]).  
[5] The CLIP LED is very useful to control the input gain. It should never be  
[17] Use this 5-digit LED meter to control the output level of the main signal.  
The upper LIM LED illuminates when the internal amp protection circuit  
responds to output levels that are too high.  
constantly illuminated (only with signal peaks).  
[6] The PAD switch reduces the input sensitivity of the channel by approx.  
30 dB, to connect for example line-level signals.  
[18] The MAStER control is used to adjust the main output volume.  
[7] The balanced LINE IN input (1" TRS) can be used for line-level signal  
sources, e.g. keyboards.  
2.3.1 Connectors  
[8] Each channel has a balanced MIC microphone input with XLR connectors.  
[19] The CD/tAPE IN connector (RCA) allows you to feed in external stereo  
signals, e.g. from a CD player, tape deck or other line-level source.  
Please remember to use either the microphone or the line input of a  
channel at a time, but never both at the same time!  
[20] The REC OUt (RCA) provides line-level signals from the power mixer to a  
DAT recorder, for example (two identical mono signals).  
2.2 Effects section  
If the REC OUT signal is connected to a recorder whose output signal  
is returned to the CD/TAPE IN, feedback can occur when you activate  
the record function. So, disconnect the CD/TAPE IN from the recorder,  
before you start recording!  
[9] Be sure that the CLIP LED illuminates for signal peaks only. If it is illuminated  
all the time, it is a sign that the effects processor is overloading and hence  
producing unpleasant distortion. The SIG LED below illuminates when the  
effects processor receives an input signal.  
[21] The PMP518M features an AMP INSERt connector for different applications.  
You can use just the power stage of the mixer for connecting a preamp for  
example. For this application you can use a 1" TS connector where the signal  
is sent over the tip of the plug. Additionally you can use the AMP INSERT  
as output, so you can use just the mixer section and connect a separate  
power amp here. For this application you have to use a 1" TRS connector,  
because the signal is send over the ring of the plug.  
[10] The EFFECt display shows the currently selected preset.  
[11] Turn the PROGRAM control to select an effects preset  
(preset number starts flashing). Push the control briefly to  
confirm your selection.  
[12] Press the FX IN button to activate the effects processor.  
[22] Use the POWER switch to put the unit into operation. The POWER switch  
should always be in the “Off” position when you are about to connect the  
unit to the mains.  
Please note: The POWER switch does not fully disconnect the unit from  
the mains. Unplug the power cord completely when the unit is not used  
for prolonged periods of time.  
behringer.com  
 
 
7
EUROPOWER PMP518M User Manual  
[24]  
{25]  
[23]  
[27]  
[26]  
Fig. 2.2: Rear panel control elements and connectors  
2.4 Rear panel  
[23] The mains connection is on a standard IEC receptacle. An appropriate power  
4. Installation  
4.1 Mains connection  
cord is supplied with the unit.  
Blown fuses must be replaced by fuses of the same type and rating.  
[24] FUSE HOLDER. Before connecting the unit to the mains, ensure that  
the voltage setting matches your local voltage. Blown fuses should only  
be replaced by fuses of the same type and rating. Please also read the  
information given in chapter 6 “Specifications”.  
The mains connection is made using the enclosed power cord and a standard IEC  
receptacle. It meets all of the international safety certification requirements.  
Please make sure that all units have a proper ground connection.  
For your own safety, never remove or disable the ground conductor  
from the unit or of the AC power cord.  
[25] The three PARALLEL SPEAKER OUtPUts provide the mono main signal on  
a Neutrik Speakon-compatible connector (pins 1+/1- and 2+/2-) and on two  
1" TS connectors.  
4.2 Audio connections  
The impedance of the loudspeaker connected must not fall below 4 Ω.  
The inputs and outputs of the BEHRINGER EUROPOWER are unbalanced  
1" TS connectors — except for the balanced mono line inputs and the  
balanced XLR inputs. Of course, all inputs and outputs work with both balanced  
and unbalanced connectors. The Tape Ins and Outs are on RCA connectors.  
Information on how to properly connect your speaker with regard to  
polarity can be found on the rear of the mixer (PINOUTs).  
[26] This is the cooling fan of the unit.  
[27] SERIAL NUMBER.  
Please ensure that only qualified personnel install and operate the  
power mixer. During installation and operation, the user must have  
sufficient electrical contact to earth. Electrostatic charges might affect  
the operation of the unit.  
3. Digital Effects Processor  
100 FIRST-CLASS EFFECTS  
Unbalanced ¼" TS connector  
Strain relief clamp  
Sleeve  
The PMP518M features a built-in digital effects processor. This effects processor  
offers a large number of standard effects such as Hall, Chorus, Flanger, Delay and  
various combination effects. Using the FX control, you can feed signals into the  
effects processor. The integrated effects module has the advantage of requiring  
no wiring. This way, the danger of creating ground loops or uneven signal levels  
is eliminated at the outset, completely simplifying the handling.  
Tip  
Presets 00 - 09:  
Presets 10 - 19:  
Presets 20 - 29:  
Presets 30 - 39:  
Presets 40 - 49:  
Presets 50 - 59:  
Presets 60 - 69:  
Presets 70 - 79:  
Presets 80 - 89:  
Presets 90 - 99:  
Hall  
Room  
Plate  
Sleeve  
(ground/shield)  
Gated/Reverse  
Early Reflections  
Delay  
Tip  
(signal)  
Chorus  
Phase/Pitch  
Multi 1  
Fig. 4.1: 1" TS connector  
Multi 2  
behringer.com  
 
 
8
EUROPOWER PMP518M User Manual  
Balanced ¼" TRS connector  
strain relief clamp  
tip  
tip  
sleeve  
ring  
tip  
sleeve  
sleeve  
shield  
Fig. 4.4: RCA cable  
4.3 Loudspeaker connection  
sleeve  
Your EUROPOWER is equipped with high-quality Neutrik Speakon-compatible  
loudspeaker connectors, which ensure safe and trouble-free operation.  
The Speakon connector was especially developed for high-power loudspeakers.  
Once it is plugged in, it safely locks into position and cannot be accidentally  
disengaged. It prevents the occurrence of electrical shock and ensures the  
correct polarity. Each of the connectors carries only the assigned single signal  
(see tab. 4.1/fig. 4.5 and the information on the rear panel of the power mixer).  
ground/shield  
ring  
cold (-ve)  
tip  
hot (+ve)  
For connection of balanced and unbalanced plugs,  
ring and sleeve have to be bridged at the stereo plug.  
Professional speaker connector  
(compatible with Neutrik Speakon connectors)  
Fig. 4.2: 1" TRS connector  
Balanced use with XLR connectors  
1+  
2-  
1+  
2-  
2
1
1-  
1-  
3
2+  
2+  
front view  
rear view  
input  
1 = ground/shield  
2 = hot (+ve)  
Fig. 4.5: Loudspeaker connector  
3 = cold (-ve)  
Please be sure to only use commercial Speakon cables (type NL4FC) for  
connecting your loudspeakers to the mixer. Please check the pin connections  
of your loudspeakers and cables depending on the EUROPOWER speaker output  
you choose.  
1
2
3
EUROPOWER PMP518M  
output  
1+  
1-  
2+  
2-  
OUtPUt  
For unbalanced use, pin 1 and pin 3 have to be bridged  
MAIN MONO  
POS  
NEG  
POS  
NEG  
Fig. 4.3: XLR connectors  
Tab. 4.1: Pin connections of the professional loudspeaker connector  
behringer.com  
 
 
9
EUROPOWER PMP518M User Manual  
5. Applications  
This illustration shows just one example of how the channels of your power mixer The following illustration shows a live application with the PMP518M as monitor  
can be used, including the connection of mono and stereo sources, and the tape  
ins and outs recording the mix signal or playing back external signals.  
mixer and a BEHRINGER EURODESK SL2442FX-PRO that provides the FOH main  
mix signal. The PMP518M receives the Aux Send signal of the EURODESK that is  
used for the monitor mix on stage.  
EUROLIVE  
E1520A  
EUROLIVE  
E1520A  
FOH Mix  
EUROPOWER  
EP2000  
Tape  
In/Out  
DAT Recorder  
Vocal mic  
ULTRA-G  
GI100  
Keyboard  
EURODESK  
SL2442FX-PRO  
Aux  
Send  
Electric Bass  
V-AMP 2  
Electric Guitar  
EUROPOWER PMP518M  
Fig. 5.1: Standard set-up  
Monitor Mix  
Fig. 5.2: Setup with PMP518M as monitor mixer  
behringer.com  
 
 
10 EUROPOWER PMP518M User Manual  
6. Specifications  
Microphone Inputs  
DSP  
Type  
XLR, electronically balanced  
Converter  
24-bit Sigma-Delta,  
40 kHz  
Mic E.I.N. (20 Hz - 20 kHz)  
@ 0 Ω source resistance  
@ 50 Ω source resistance  
@ 150 Ω source resistance  
Frequency response  
Sampling rate  
-122 dB / -125 dB A-weighted  
-122 dB / -125 dB A-weighted  
-121 dB / -124 dB A-weighted  
Display  
Type  
2-digit, 7-segment LED  
Amplifier  
< 10 Hz - 100 kHz (-1 dB),  
< 10 Hz - 200 kHz (-3 dB)  
Output power  
(RMS @ 1 % THD (sine wave))  
62 W (8 Ω), 105 W (4 Ω)  
100 W (8 Ω), 180 W (4 Ω)  
Gain  
+33 dB, +8 dB with pad  
+12 dBu @ 10 dB gain  
Output power  
(Peak Power)  
Max. input level  
Impedance  
approx. 2.2 kΩ balanced,  
1.1 kΩ unbalanced  
Power Supply  
Signal-to-noise ratio  
Distortion (THD+N)  
110 dB/114 dB A-weighted  
(-11 dBu in @ +33 dB gain)  
Mains voltages  
U.S./Canada  
120 V~, 60 Hz  
0.001% / 0.0008% A-weighted  
China/Korea  
220 V~, 50/60 Hz  
230 V~, 50 Hz  
Mono Line Inputs  
Type  
Europe/U.K./Australia  
Japan  
1" TRS connector, balanced  
100 V~, 50 - 60 Hz  
120/230 V~, 50 - 60 Hz  
max. 290 W  
Impedance  
approx. 80 kΩ balanced,  
40 kΩ unbalanced  
General export model  
Power consumption  
Fuse  
Max. input level  
+30 dBu  
100 - 120 V~: T 6.3 A H 250 V  
220 - 240 V~: T 3.15 A H 250 V  
EQ  
Mains connection  
Standard IEC receptacle  
Low  
High  
80 Hz / 15 dB  
12 kHz / 15 dB  
Physical / Weight  
Dimensions (H x W x D)  
approx. 4 3/5x 18 1x 8 7/8"  
approx.117 x 470 x 225 mm  
Main Mix System Data  
Noise  
Weight (net)  
approx. 15.88 lbs / 7.2 kg  
Main mix @ -∞,  
Channel fader -∞  
-106 dB / -110 dB A-weighted  
-87 dB / -90 dB A-weighted  
-80 dB / -82 dB A-weighted  
Main mix @ 0 dB,  
Channel fader -oo  
Main Mix @ 0 dB,  
Channel fader @ 0 dB  
Loudspeaker Outputs  
Type  
Neutrik Speakon-compatible,  
1" TS connectors  
Load impedance  
4-16 Ω  
behringer.com  
 
 
11 EUROPOWER PMP518M User Manual  
FEDERAL COMMUNICATIONS  
COMMISSION COMPLIANCE  
INFORMATION  
EUROPOWER PMP518M  
Responsible party name:  
Address:  
MUSIC Group Services USA, Inc.  
18912 North Creek Parkway,  
Suite 200 Bothell, WA 98011,  
USA  
Phone/Fax No.:  
Phone: +1 425 672 0816  
Fax: +1 425 673 7647  
EUROPOWER PMP518M  
complies with the FCC rules as mentioned in the following paragraph:  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined  
by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This device complies with Part 15 of the FCC rules. Operation is subject to the  
following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may  
cause undesired operation.  
Important information:  
Changes or modifications to the equipment not expressly approved by MUSIC Group  
can void the user’s authority to use the equipment.  
behringer.com  
 
behringer.com  
 

321 Studios Chipper Plesk 7x Reloaded User Manual
ACDelco Automobile Parts 26 SI User Manual
Acer Laptop 2350 User Manual
AEG Washer 76730 User Manual
Alcatel Carrier Internetworking Solutions Switch 6624 User Manual
Allied Telesis Network Cables AT MC606 User Manual
American DJ DJ Equipment Flight Moon User Manual
ATI Technologies Computer Hardware X1950 PRO User Manual
Bakers Pride Oven Kitchen Entertainment Center PHC70 MPINS User Manual
Barco Air Conditioner 08 0311105 00 User Manual