Audiovox Remote Starter APS 786 User Manual

Model APS 786  
Installation Manual  
4 Channel Remote Car Starter  
With Full Feature Alarm System  
Installation Instructions  
This Unit Is Intended For Installation In Vehicles With  
12 Volt Negative Ground Electrical Systems,  
Gasoline or Diesel With True Tach Reference  
And Automatic Transmissions Only.  
Kit Contents:  
Remote Start/Alarm Control Module  
(2) - Four Button Anti Code Hopping Transmitters  
4 Channel Code Learning Receiver  
External Superheterodyne Antenna/Receiver  
Mini Six Tone Siren  
(1) - Multi Pin Input/Output Harness  
(1) - Six Pin Power Harness  
(1) - Four Pin Auxiliary Output Harness  
(1) - Two Pin LED Indicator  
(1) - Two Pin Valet / Programming Switch  
(1) - Two Pin Control Switch  
(1) - Four Pin Shock Sensor Harness  
(1) - Two Pin Door Lock Harness  
(1) - Dual Stage Shock Sensor  
(1) - Starter Inhibit Relay and Socket  
(2) - 30 Amp In-line Fuse Holders With Fuses  
(1) - Pin Switch Hardware Bag  
(2) - Under Hood Caution Labels  
(1) - Installation Manual  
(1) - Operator's Manual  
(1) - Limited Warranty  
(2) - Window Decals  
128-6531  
1 of 24  
 
THE RECEIVER/ANTENNA ASSEMBLY:  
The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the  
dash board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle  
for best reception. Special considerations must be made for windshield glass as some newer vehicles  
utilize a metallic shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the  
antenna toward a rear window location for best reception. Secure the antenna with double stick tape  
provided. After securing the antenna with tape, we advise also securing a section of the antenna cable to a  
fixed support. This will prevent the antenna from dropping down in case the double stick tape is exposed to  
extreme heat which may loosen it's gummed surface. Route the 3 pin connector toward the control module  
using caution not to pinch the cable as this will cause poor or no RF reception to the control module.  
VALET/PROGRAM/MANUAL OVERRIDE SWITCH :  
Select a mounting location that is easily accessible to the operator of the vehicle. It is not necessary to  
conceal the switch. However, concealment is recommended as it offers a higher level of security. The  
switch can be mounted to the lower dash panel in the driver's area. Inspect behind the chosen location to  
insure that adequate clearance is allowed for the body of the switch, and also that the drill will not penetrate  
any existing factory wiring or fluid lines. Drill a 5/32" hole in the desired location and mount the switch by  
passing it through the panel from the underside. Secure the switch using the nut and star washer. Route  
the switch's connector toward the control module.  
NOTE: During the program sequence, there are times when this switch and the ignition switch will be used  
simultaneously. We recommend that the push-button switch be mounted on the left side of the ignition switch to  
facilitate this operation.  
CONTROL SWITCH:  
Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick  
panel, or glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is  
allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid  
lines. Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the  
underside. Secure the switch using the nut, star washer, and on/off face plate. It is suggested that the  
switch be oriented to allow the on position to be up toward the driver and the off position to be down or away  
from the driver. Route the switch's connector toward the control module.  
SHOCK SENSOR:  
Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation  
from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing  
and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self  
taping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie straps.  
Whichever mounting method is used be sure to allow access to the sensitivity adjustment potentiometer for  
use later in the installation.  
STARTER INHIBIT RELAY:  
Select a mounting location within 12" of the ignition switch's low current start solenoid wire. Secure the relay  
to an existing harness in the chosen location using a cable tie around the relay's wiring harness. Caution!  
Do not wire tie the metal bracket to an existing wiring harness as vibration may cause chaffing and shorting  
damaging the factory wiring. If an existing harness is not available then secure the relay's metal mounting  
tab to an under dash metal brace with a #8 self taping sheet metal screw. Wire the relay as per the diagram  
found later in this manual.  
The APS-785 is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination  
Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed  
into a vehicle with a manually operated transmission. Doing so may result in serious personal injury and  
property damage.  
IMPORTANT!  
DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS  
INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE.  
AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE  
BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.  
3
128-6531  
3 of 24  
 
WIRING THE 6 PIN MAIN POWER HARNESS:  
RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source  
Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse  
and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2  
relays.  
RED Wire: + 12 Volts Battery 2 Source  
Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse  
and holder provided, but NOT the same vehicle wire as used by the battery 1 source. Most vehicles have  
more than one battery source supplying power to the ignition switch. Separate feed wires must be used for  
the Red and Red/White wires. If your vehicle does not have two battery feed wires at the ignition switch then  
it is possible to connect both wires to the vehicle's battery. This wire provides power for the start relay and  
the accessory relay.  
IMPORTANT!  
It is the responsibility of the installing technician to determine the load factor of the vehicles electrical circuits  
when the vehicle is running, and to adequately fuse the two power wires based on that load. If the vehicle,  
running under load with the air conditioner, heater blower motor, and accessories exceed 24 Amps continu-  
ous, we recommend that two fuses be used in combination on each power wire as shown below. For  
additional information see Tech Update issued 9/30/96.  
YELLOW Wire: Starter Output  
Careful consideration for the connection of this wire must be made to prevent the vehicle from  
starting while in gear. Understanding the difference between a mechanical and an electrical Neutral  
Start Switch will allow you to properly identify the circuit and select the correct installation method.  
In addition you will realize why the connection of the safety wire is required for all mechanical  
switch configurations.  
Failure to make this connection properly can result in personal injury and property damage.  
In all installations it is the responsibility of the installing technician to test the remote start unit and assure  
that the vehicle cannot start via RF control in any gear selection other than park or neutral.  
In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wire will  
be made to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts  
when the ignition switch is turned to the start (crank) position only. This wire will have 0 volts in all other  
ignition switch positions.  
NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the  
electrical neutral switch configuration, this connection must be made between the starter inhibit relay,  
( when used ) and the neutral safety switch as shown in the following diagram.  
Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal  
injury and property damage.  
SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.  
BLUE Wire: Ignition 1 Output  
Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the  
ignition key is turned to the "ON" or "RUN" and the "START" or CRANK" positions, and will have 0 volts  
when the key is turned to the "OFF" and "ACCESSORY" positions.  
For Diesel Applications, this wire must be connected to the ignition circuit that powers the glow plugs if the  
vehicle requires glow plug pre-heating. (See selectable feature #9)  
4
128-6531  
4 of 24  
 
YELLOW START WIRE DETAIL  
GREEN Wire: Ignition 2 Output  
Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the  
ignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.  
This wire will show 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions.  
NOTE: See programming information concerning this wire to allow output during the "START" mode.  
VIOLET Wire: Accessory Output  
Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the  
ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions, and will show 0 volts when the  
key is turned to the "OFF" and "START" or "CRANK" positions.  
5
128-6531  
5 of 24  
 
WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness  
White w/ Red Trace Wire: Parking Light Flasher Feed  
This wire is the common contact of the on board parking light flasher relay. If the vehicle you are  
working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15  
Amps)  
NOTE: If the vehicle's parking lights are ground switched, connect this wire to chassis ground.  
White Wire: Parking Light Flasher Output  
This wire is the normally open contact of the on board parking light flasher relay. Connect this wire to the  
vehicle parking light feed wire. See diagram below for details on wiring positive switched parking light  
circuits.  
Parking Light Wiring Detail  
White w/ Black Trace Wire: (+) Siren Output  
This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren  
location. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wire  
of the Siren to a known chassis ground or solid clean metal surface.  
Siren Wiring Detail  
SIREN  
TO WHITE w/BLACK WIRE OF MODULE  
z
(-) TO VEHICLE'S CHASSIS GROUND  
6
128-6531  
6 of 24  
 
Purple Wire: (+) Door Trigger Input  
If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and some  
Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches.  
In most cases, the Purple wire will need to be connected to only one door switch no matter how many  
doors the vehicle has as most door lighting circuits are wired in parallel.  
Note for vehicles with interior delay lighting see programming under title "Completing The Installation".  
Positive Door Switch Wiring Detail  
Dark Green Wire: (-) Instant Trigger Input  
This is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin  
switches previously installed.  
Note: This wire will be shunted when remote control channel 3 is accessed, (trunk release). This wire  
will remain shunted all the while there is ground present and for 5 seconds after the ground is removed.  
This allows the operator to open the trunk via the remote transmitter without having to first disarm the  
alarm system. See below for wiring detail.  
Hood Pin Switch Detail  
7
128-6531  
7 of 24  
 
Light Blue Wire: Ignition 3 Output  
This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit  
initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit  
turns off. In all of the applications described below, a relay will be required.  
The Light Blue wire can be used to accommodate the following situations:  
A. Shock Sensor By Pass:  
If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the  
Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger.  
In this case, connect the Light Blue Wire to terminal #86 of a external relay. Connect terminal # 85 of  
the relay to a fused + 12 volt battery source. Cut the shock sensor trigger wire and connect one end  
of the cut wire to terminal #30 and the other end of the cut wire to terminal #87a. Just before the  
Remote Start unit is activated, the relay contacts will open, preventing the shock sensor's operation  
until the Remote Start unit shuts off.  
B. Ignition 3 Output:  
Some newer vehicles use a third ignition wire which is required to start and keep the vehicle's engine  
running. If this is the case, connect the Light Blue wire to terminal #86 of an external relay. Connect  
terminal # 30 & # 85 to a fused + 12 volt battery source rated for a minimum of 25 Amp. Connect  
terminal # 87 to the third ignition wire in the vehicle.  
C. GM VATS Key Override:  
If the vehicle has the General Motors VATS system installed, you will need to by-pass the system  
while the vehicle is operating under the control of the Remote Start Unit. To Do This;  
1. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of  
the key's value from the resistor pack supplied.  
2. Locate the pair of VATS wires in the vehicle, usually a pair of thin gauge wires running from the  
ignition switch to the VATS control module.  
NOTE: These wires are typically White w/ Black trace and Violet w/ Yellow trace, however in later model  
Cadillacs, they are run through an orange sleeve, and are either both Black, both Yellow, or both White  
wires. Consult the factory service manual for additional information.  
3. Connect the Light Blue Wire from the Remote Start Unit to terminal #86 of an external relay.  
Connect terminal #85 of the relay to a fused + 12 volt battery source.  
4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the  
relay. Connect the other side of the (#1) wire to terminal #30.  
5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown).  
NOTE: The above information and following diagram is for the GM VATS system only. For GM PASS  
LOCK System you will require the Audiovox AS-PASS II Module.  
General Motors VATS By-Pass Diagram  
8
128-6531  
8 of 24  
 
Green w/ White trace Wire: Entry Illumination Ground Output  
This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the  
alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered.  
This wire should be connected to an external relay, and wired to the vehicles interior entry lighting  
whenever the optional Interior Illumination circuit is desired. See below for relay wiring details.  
Entry Illumination Detail  
Grey w/ Black Trace Wire: Negative Inhibit Input  
The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module when-  
ever it is grounded. Connect the Grey w/ Black trace wire to the hood pin switch previously installed.  
This wire must be routed through a grommet in the firewall and connected to the hood pin switch. If the  
pin switch is to be used with an alarm system, connect this wire using the diode assembly provided.  
IMPORTANT! This connection is a safety wire and must be connected as shown and tested as specified.  
Failure to do so may result in personal injury or property damage. See detail of wiring in the following  
diagram. This wire may also be used if the vehicle brake light circuit switches ground to the brake lights.  
An isolation diode must be used for ground switched brake light circuits and must be connected to the  
output of the brake switch.  
Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail  
9
128-6531  
9 of 24  
 
Orange Wire: Ground When Armed Output  
This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit  
relay. Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal  
#85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts when the ignition switch is  
turned to the on and start positions and off when the key is off. Locate and cut the low current start  
solenoid wire found at the vehicles ignition switch harness. This wire will have + 12 volts when the  
ignition key is moved to the start (crank) position and will have 0 volts in all other key positions. Connect  
one side of the cut wire to terminal #87a ( Black wire) of the relay. Connect the other side of the cut wire  
to terminal #30 (White/Black wire) of the relay. See below for detail of wiring, also see Yellow Start wire  
detail for connection to vehicle considerations.  
Starter Inhibit Wiring Detail  
Black  
White/Black  
Brown w/ Black Trace Wire: Positive Inhibit Input  
The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module  
whenever it gets + 12 volts. If the Brake lights switch in the vehicle switches + 12 volts to the brake light  
circuit, connect the Brown w/ Black trace wire to the output side of the brake switch. This will allow the  
Remote Start to shut down if an attempt is made to operate the vehicle without the key while running  
under the control of the Remote Start. In most vehicles, in order to shift into gear, the brake pedal must  
be depressed. The brake input will in turn cause the remote start unit to shut off. See detail in the  
following diagram for wiring the brake light circuit.  
Brake Switch Positive Shutdown Detail  
10  
128-6531  
10 of 24  
 
Black Wire: Chassis Ground Source  
Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis.  
Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal.  
Chassis Ground Connection Detail  
Green w/ Orange Trace Wire: Tachometer Input Signal  
This wire will continually monitor the engine's tach rate while the unit is under power of the Remote Start  
module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine  
compartment and connect to the negative side of the ignition coil. This Remote Start unit learns the tach  
rate of the vehicle and in most cases will operate properly from one multi coil pack regardless of the  
number of cylinders. If the vehicle has a single coil unit for each cylinder, it may be necessary to connect  
this wire to more than one cylinder for proper tach reference. See multi coil wiring detail shown later in  
this manual for additional information.  
Tachometer Input Wiring Detail  
Brown Wire: Negative Door Trigger  
If the vehicle's door courtesy light switches ground when the door is opened, (Most GMs and Imports),  
you must connect this wire to the negative output from one of the vehicle's door pin switches. In most  
cases the Brown wire will need to be connected to only one door switch no matter how many doors the  
vehicle has as most door lighting circuits are wired in parallel.  
Note for vehicles with interior delay lighting see programming under title "Completing The Installation".  
Negative Door Switch Wiring Detail  
11  
128-6531  
11 of 24  
 
Dark Blue Wire: Delayed 300mA Pulsed Channel 3 Output  
The Dark Blue wire supplies a 300mA ground pulsed output whenever channel three of the receiver is  
accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two.  
This is a low current output and must be connected to a relay to supply power to the trunk release or the  
circuit you wish to control. Connect the Dark Blue wire to terminal # 86 of a VF45F11 P&B relay or equivalent.  
Connect terminal # 85 of the relay to a fused + 12 volt source. Connect the common, normally open, and  
normally closed contacts of the relay to perform the selected function of channel 3. See below for relay  
wiring detail.  
Channel 3 Relay Wiring Detail  
Green w/ Black Trace Wire: 300mA Latched Channel 4 Output  
The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiver  
is accessed. Pressing the pre-programmed transmitter button(s) will access channel four and will remain  
active, for up to 8 seconds, as long as the transmitter button(s) is held. This is a low current output and must  
be connected to a relay to supply power to the device you intend to control. Connect Green w/ Black Trace  
wire to terminal #86 of a VF45F11 P&B relay or equivalent. Connect terminal #85 of the relay to a fused +  
12 volt source. Connect the common, normally open, and normally closed contacts of the relay to perform  
the selected function of the channel 4 output.  
Dark Blue/Black Trace Wire: External Trigger Input  
The Dark Blue/Black trace wire allows the remote start unit to be activated from an external source. The  
intent of this wire is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar  
device. When this wire receives a ground pulse, the unit will start the vehicle. Connect this wire to a ground  
pulsed output from the controlling circuit.  
Black w/ White Trace Wire : 300 mA Horn Output  
The black w/ white trace wire is provided to beep the vehicle’s horn. This is a transistorized low current  
output, and should only be connected to the low current ground output from the vehicle’s horn switch.  
If the vehicle uses a + 12 VDC horn switch, then connect the black w/ white trace wire to terminal 86 of the  
AS 9256 relay ( or an equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12  
VDC battery source. Connect relay terminal 87 to the vehicle’s horn switch output, and connect relay termi-  
nal 30 to a fused + 12 VDC battery source.  
WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS  
The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during  
different stages of the Remote Start unit's operation. Understanding these outputs and the time in which  
they occur will allow you to determine if they are needed for the particular vehicle you are working on as well  
as how to use them.  
Black w Blue Trace Wire: Pulsed Ground Output Before Start  
The Black w/ Blue Trace wire will provide a 1 second 300 mA pulsed ground output 1.5 second before the  
remote start unit activates as well as when the transmitter is used to disarm the system. Typical use for this  
output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm  
when the remote start unit engages or when the 785 is used to unlock the doors.  
Black w/ Light Green Trace Wire: Pulsed Ground Output After Start  
The Black w/ Light Green Trace wire will provide a 1 second mA pulsed ground output after the vehicle is  
12  
128-6531  
12 of 24  
 
started under control of the remote start unit. Typically this wire will be used to re-lock the vehicle doors if  
the doors unlock automatically when the factory anti-theft system is disarmed.  
Black w/ Red Trace Wire: Pulsed Ground Output After Shutdown  
The Black w/ Red Trace wire will provide a 1 second 300 mA pulsed ground output after the remote start unit  
shuts down. This output will occur regardless of whether the circuit times out or is manually terminated.  
Typically this output will be used to re-lock the vehicle doors if the doors unlock automatically when the  
ignition circuit transitions to off.  
Black w/ Yellow Trace Wire: Ground Output During Start (Crank)  
The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote  
start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM  
vehicles. This wire is also referred to as the ECM wake up wire in some vehicles.  
NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement  
is more than 300mA.  
2 Pin Control Switch: (Red Connector)  
The Black & Black w/White Trace wires loaded in the two pin red connector enable the operation of the  
Remote Start unit. When the Black w/ White Trace wire is grounded, the remote start unit is operable.  
When this wire is open from ground, the remote start is disabled. Route the twin lead Black & Black w/  
White Trace wires from the control switch to the remote start unit and plug red two pin connector into the  
mating red two pin connector shell of the control module.  
4 Pin Shock Sensor: (White Connector)  
The Red (+12 volt), Black (ground), Blue (pre-detect) and Green (full trigger when armed) wires loaded into  
the white connector shell are the inputs/outputs of the shock sensor. Route the 4 wire harness from the  
shock sensor to the remote start control unit and plug the 4 pin white connector into the mating 4 pin  
connector shell of the control module.  
Note: While operating under the control of the remote start unit the shock sensor will be shunted (by-passed).  
Once the remote start shuts down, the shock sensor will be re-enabled.  
2 Pin LED Harness: (White Connector)  
The Red & Blue wires loaded into the two pin mini white connector control the anode and cathode of the  
dash mounted LED. Route the twin lead Red and Blue wires from the LED to the remote start control unit  
and plug the two pin connector into the mating white mini connector shell of the control module.  
2 Pin Valet/Program/Override Push-Button Switch: (Blue Connector)  
The Black & Grey twin lead wires loaded in the two pin blue connector are the ground supply and program/  
valet/override input of the Remote Start unit. When the Grey wire is grounded, under certain conditions, the  
unit will enter the valet mode. When the Grey wire is sequentially grounded under other conditions, the unit  
will enter the various program modes. Route the twin lead Black and Grey wires from the valet/Program  
switch to the remote start unit and plug the two pin connector into the mating blue connector shell of the  
control module. Refer to the remote programming, feature programming and function programming shown  
later in this installation guide for operation of the valet/program switch. For override information, refer to the  
owners manual.  
3 Pin Antenna/Receiver Connector:  
Plug the previously routed three pin connector from the antenna receiver assemble into the mating connec-  
tor of the control module. This connector supplies 12 volts, ground and RF data from the antenna receiver  
to the remote start module. Be certain this connector is firmly seated making good contact to the control  
unit.  
3 Pin Door Lock/Unlock Harness: (White Connector)  
The Red and Green wires will provide either a pulsed ground output to the factory door lock control relay, or  
a pulsed + 12 volt output to the factory door lock control relay. In either case, the maximum current draw  
through these outputs must not exceed 300mA. The Red w/Black trace wire will provide a pulsed ground  
only, and will only provide an output when the unlock button of the transmitter is pressed a second time after  
a first unlock command was issued. This is used for second step unlock or all doors unlock in a two step  
circuit. In this arrangement, Red is used to control the drivers door unlock relay, and the Red/Black will be  
used to control unlock of all other doors.  
13  
128-6531  
13 of 24  
 
3 Wire Ground Switched Door Lock Circuits:  
In this application, the Red wire of the door lock harness provides a ground pulse during the arming se-  
quence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the  
factory door lock switch to the factory door lock relay.  
The Green wire of the door lock harness provides a ground pulse during the disarming sequence, or pulsed  
ground unlock output. Connect the Green wire to the low current ground signal wire from the factory door  
unlock switch to the factory door unlock relay. See Below For Wiring Detail.  
3 Wire Ground Switched Door Lock/Unlock Wiring Detail  
3 Wire Positive Switched Door Locks:  
In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming  
sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from  
the factory door unlock switch to the factory door unlock relay.  
The Green wire of the door lock harness provides a + 12 volt pulse during the arming sequence, or pulsed  
12 volt lock output. Connect the Green wire to the low current 12 volt signal wire from the factory door lock  
switch to the factory door lock relay. See Below For Wiring Detail.  
3 Wire Positive Switched Door Lock/Unlock Wiring Detail  
3 Wire Ground Switched 2 Step Door Locks  
In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output.  
Connect the red wire to the wire that provides a low current ground signal from the factory door lock switch  
to the factory door lock control relay.  
The green wire provides the first ground pulse during disarming, or the drivers door pulsed ground  
unlock output. Connect this wire to the drivers door unlock relay that requires a low current ground signal  
to unlock only the drivers door. If the vehicle does not have a separate drivers door relay, one will have to be  
added. Locate the drivers door unlock motor wire and cut it at a convenient location to allow wiring of an  
optional relay. Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect the  
vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the green wire of the 3 pin  
harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay added to a  
fused constant + 12 volt source. Most vehicles door lock/unlock motor legs rest at ground, and switch +12  
volts to the door lock/unlock motor legs for operation, if this is the case in the vehicle you are working on,  
connect the remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle door  
14  
128-6531  
14 of 24  
 
lock/unlock motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect the  
remaining terminal, 87, to chassis ground.  
The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a  
second time after disarming. Connect the Red/Black wire to the wire that provides a low current ground  
signal from the factory door unlock switch to the factory door unlock control relay.  
3 Wire Positive Switched 2 Step Door Locks  
The green wire provides a positive pulse during arming, or the pulsed + 12 volt lock output. Connect the  
green wire to the wire that provides a low current positive signal from the factory door lock switch to the  
factory door lock control relay.  
The red wire provides a positive pulse during disarming, or the drivers door pulsed positive unlock  
output. Connect this wire to the drivers door unlock relay that requires a low current positive signal to  
unlock only the drivers door. If the vehicle does not have a separate drivers door relay, one will have to be  
added. Locate the drivers door unlock motor wire and cut it at a convenient location to allow wiring of an  
optional relay. Connect the door side of the cut wire to terminal 30 of the optional relay added. Connect the  
vehicle side of the cut wire to terminal 87a of the optional relay added. Connect the red wire of the 3 pin  
harness to terminal 86 of the optional relay added. Connect terminal 85 of the optional relay added to  
chassis ground. Most vehicles door lock/unlock motor legs rest at ground, and switch +12 volts to the door  
lock/unlock motor legs for operation, if this is the case in the vehicle you are working on, connect the  
remaining terminal, 87, to a fused + 12 volt source. In the rare instance that the vehicle door lock/unlock  
motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect he remaining  
terminal, 87, to chassis ground.  
The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a  
second time after disarming. Because the vehicle you are working on requires a positive pulse from the  
factory door lock switch to the factory door lock control relay, you will have to add a relay to invert the output  
polarity of this wire. Connect the Red/Black wire to terminal 86 of the optional added relay. Connect  
terminal 85 & 87 to a fuse + 12 volt source. Connect terminal 30 to the low current door unlock wire from the  
factory door switch to the door unlock control relay.  
15  
128-6531  
15 of 24  
 
Note: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt  
Door Lock Control Circuits  
These applications require the use of additional components which may include relays, fixed resistors, or  
for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supple-  
ment and or the Audiovox fax back service for information on your particular vehicle for properly connect-  
ing to these types of circuits.  
ALARM SELECTABLE FEATURES  
NOTE: The Alarm Selectable Features and Remote Start Selectable Features programming steps following are  
based on transmitter button 1 being programmed for channel 1 and transmitter button 2 being programmed for  
channel 2.  
RF Programmable Features:  
Feature Selection  
1st Door L/UL  
1 Chirp  
1 Sec.  
2 Chirps  
3.5 Sec.  
3 Chirps  
Default  
1 Sec.  
1 Sec L, Dbl. U/L  
2nd Accy Lock  
Auto Lock On  
Auto UL Dr  
Passive  
Auto Lock Off  
Auto UL All  
Active  
Auto Lock Off  
Auto UL Off  
Active  
3rd Accy. UL  
Auto Off  
4th Passive Locks  
5th Passive/Active Arm  
6th Siren/Horn  
Passive Arm  
Siren/Horn  
10mS  
Active Arm  
Siren Only  
16mS  
Active Arm  
Siren/Horn  
16mS  
Horn Only  
30mS  
7th Horn Chirp  
8th Override Method  
9th Two Step Unlock  
10th Chirp Delete From Tx  
Custom Code  
On  
Valet  
Valet  
Off  
Off  
On  
Off  
Off  
16  
128-6531  
16 of 24  
 
To program these selectable features;  
Action  
Turn ignition on  
System Response  
No response  
Press and release the valet switch 3 times  
Within 3 seconds, turn ignition Off  
1 Chirp - LED 1 flash  
Short chirp, then long chirp  
First  
Then On  
1 chirp = 1 second door locks  
Press transmitter Lock button to change  
Press transmitter Lock button to change  
or  
2 chirps = 3.5 second door locks  
3 chirps = 1 sec. lock, dbl 1 sec. unlock  
Second  
Third  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
Press and release the valet switch  
Press transmitter Lock button to change  
Press transmitter Lock button to change  
or  
2 chirps = auto locks off  
1 chirp = auto locks on  
3 chirps = auto unlock off  
1 chirp = auto unlock drivers door only  
2 chirps = auto unlock all doors  
Fourth  
Fifth  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
2 chirps = active locks  
1 chirp = passive locks  
2 chirps = active arming  
1 chirp = passive arming  
Sixth  
Press and release the valet switch  
Press transmitter Lock button to change  
Press transmitter lock button to change  
or  
1 chirp = siren and horn output  
2 chirps = siren output only  
3 chirps = horn output only  
Seventh  
Press and release the valet switch  
Press transmitter Lock button to change  
Press transmitter Lock button to change  
or  
2 chirps = horn chirp output 16mS  
3 chirps = horn chirp output 30mS  
1 chirp = horn chirp output 10 mS  
Eighth  
Ninth  
Tenth  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
2 chirps = valet switch override operation  
1 chirp = custom code override operation  
2 chirps = 2 step unlock off  
1 chirp = 2 step unlock on  
Press and release the valet switch  
2 chirps = chirp delete from transmitter inactive  
Press transmitter Lock button to change  
Press and release the valet switch  
or  
1 chirp = chirp delete from transmitter active  
Exit program mode  
Turn ignition key off  
Exit program mode  
Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps,  
or the programming will be terminated.  
17  
128-6531  
17 of 24  
 
TIMED START PROGRAM:  
The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature is  
useful in extremely cold climates where starting the engine is the only means to keep the battery charged  
and fluids warm. The operator has the option to have the unit start every 2 or 4 hours for a maximum of 48  
hours. Factory pre-set is to start at 4 hour intervals. To select 2 or 4 hour automatic start timer:  
1. Start with the Enable switch (Red Handle) in the "On" Position.  
2. Turn the ignition on then off.  
3. Within 10 seconds of the key turning off, cycle the enable switch Off, On, Off, On ( 2 times) to select a 2  
hour timed start interval. Cycle the enable switch Off, On, Off, On, Off, On, Off, On (4 times) to select a 4  
hour timed start interval. The lights will flash and the siren will chirp 2X or 4X dependant upon 2 or 4 hour  
interval setting.  
NOTE: Once selected, 2 or 4, this timer interval will remain in memory until it is manually changed. To  
change, the above sequence will have to be followed.  
TIMED START OPERATION:  
To begin the start timer, within 10 seconds of turning off the ignition switch, activate the RF command to  
start 2 times. (Press the trunk/key button four times). The lights will flash and the siren will chirp 4 times.  
Indicating timed interval mode has been initiated. The vehicle will automatically start every 2 or 4 hours as  
programmed. To cancel the timed start mode start the vehicle either by RF or by the ignition key.  
REMOTE START SELECTABLE FEATURES  
Feature  
Lts Flash 1X  
Lts Flash 2X  
On  
Lts Flash 3X  
Lts Flash 4X  
Default LED Pattern  
On 1X Pause,etc...  
10 Min 2X Pause,etc...  
Steady 3X Pause,etc...  
1 RF Start Chirp  
2 Run Time  
3 Park Lights  
4 Input Check  
5 NA  
Off  
5 Min.  
On Steady  
NA  
10 Min.  
Flash  
Tach  
15Min.  
20 Min.  
Tach  
NA  
4X Pause,etc...  
5X Pause,etc...  
6X Pause,etc...  
7X Pause,etc...  
8X Pause,etc...  
9X Pause,etc...  
NA  
NA  
6 Ign. 2 Crank  
7 Diagnostics  
8 NA  
Off  
On  
On  
Off  
NA  
On  
Off  
NA  
NA  
NA  
NA  
9 Gas/Diesel  
Gas  
Diesel 10  
Diesel 15  
Diesel 20  
Gas  
NOTE: When selecting Diesel operation, (Feature Nine), over gasoline, the only change is to the ignition  
circuits. When Diesel is selected, the ignition circuits will power up 10, 15, or 20 seconds before  
the start circuit. The intent of this feature is to allow the glow plug warming required by some diesel  
engines. If your vehicle is a instant start diesel, it is not necessary to activate this feature.  
NOTE: When selecting Diesel mode, be certain that the intended vehicle has a true tach reference and be  
certain to connect the tach input wire.  
To Program The Remote Start Selectable Features:  
1. Turn the ignition key to the On position.  
2. Press and release the valet/program switch three times.  
3. Immediately turn the ignition key Off then press transmitter trunk/key button for 1 second.  
4. Immediately turn the ignition key back On.  
5. Press and release the valet/program switch two times. The siren will emit 2 short and 1 long chirp  
verifying you are in the feature program mode.  
6. Use channel 1 button on the transmitter to advance to the feature you want to change. EXAMPLE- If you  
need to change selectable feature 3, press and release channel 1 button on the transmitter 3 times in  
succession. The parking lights will flash, and the siren will chirp 3 times confirming that selected feature  
3 can be changed.  
7. Use the trunk/key button on the transmitter to change the selection of the programmable feature. If you  
are not sure what the setting for any feature is, press the trunk/key button one time, the parking lights will  
flash one, two, three or four times indicating the features setting.  
18  
128-6531  
18 of 24  
 
NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between  
steps, or the programming mode will be terminated.  
Programming Tach Rate:  
NOTE: All applications require that tach be programmed.  
The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via the remote  
start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been  
learnedandstored. Ifthetachrateisnotproperlyprogrammedtothespecificvehicle, theunitmaynotrealize  
that the vehicle is running in certain instances reengage the starter motor.  
The Remote Start Unit will learn the tach rate of most vehicle's single coil, multiple coil packs, or single  
injector. To learn tach.  
1. Turn the ignition key to the On position.  
2. Press and release the valet/program push button switch 3 times.  
3. Immediately turn the ignition key Off.  
4. Press and hold the valet/program push button switch, then start the vehicle using the key.  
5. When the unit senses the tach signal, the parking lights will begin to flash.  
6. Release the valet/program pushbutton switch. The parking lights will turn on for three seconds to indicate  
that the learned tach signal is stored and the unit is out of the tach learn mode.  
NOTE: If the unit fails to learn tach rate due to an improper tachometer connection or a poor tach source, the  
parking lights will not flash.  
To correct this situation, locate and connect the Green/Orange wire to the proper tach signal, and then  
repeat the tach learn routine.  
Diagnostics:  
Enter selectable feature #7 and turn on as described above.  
NOTE: Diagnostic mode is a temporary mode. Once you have accessed the diagnostic mode, the unit will  
pause for two seconds then begin to flash the last stored shut down code. This code will be  
displayed two times in succession, then the unit will automatically exit the diagnostic on mode.  
The parking lights will flash a number of times indicating the reason for the last remote start shutdown. The  
light flash indications are as follows:  
1 Flash  
Run timer expired  
2 Flashes  
3 Flashes  
4 Flashes  
5 Flashes  
6 Flashes  
7 Flashes  
Low or no tach signal (RPM)  
Positive or Negative inhibit wire activation  
Control switch moved to the off position  
RF shutdown, Remote signal received, or manual start trigger wire reactivated.  
High tach signal (RPM)  
Tach signal has not been learned  
Multi Coil Pack Adaptor: (Optional)  
The multi coil pack adaptor is designed for use with vehicles having multiple ignition coils where a single  
point tach signal is unavailable, or non responsive. P/N 136B1400  
To use the adaptor, the Green/Black wires must connect to the negative side of the ignition coil(s).  
1. For vehicles utilizing independent coils per cylinder, connect the three Green/Black leads to alternate  
coils. To achieve optimum performance the coil signals must be evenly distributed. This is accomplished  
by first mapping out the firing order of the engine in groups of as indicated below. Draw a circle around  
any of the columns. The Green/Black wires should be connected to the negative (-) terminal of the  
respective cylinder number which appears in any of the circles.  
2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack.  
For 8 cylinder, four coil systems, connect to any of the three coils.  
3. Connect the Yellow wire to a +12 volt ignition 1 source. This wire will have +12 volts with the ignition in the  
on and start position and have 0 volts with the ignition in the off position.  
19  
128-6531  
19 of 24  
 
4. Connect the Green wire to the (Green) or (Orange/Green) tach input of the Audiovox remote start unit.  
TESTING YOUR INSTALLATION:  
CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start  
Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in  
the following manner may result in personal injury, property damage, or both.  
HOOD PIN SAFETY SHUT DOWN:  
The intention of the hood pin safety shut down is to prevent the Remote Start unit from being activated while  
a mechanic or vehicle owner is performing normal routine vehicle maintenance.  
To test the integrity of this circuit:  
1. With the drivers window in the down position, start the vehicle using the RF transmitter.  
2. Reach inside the car and pull the hood release.  
3. Raise the hood and confirm that the remote start unit shuts down.  
If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote  
Start Unit.  
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE  
OPERATION OF THE HOOD PIN SAFETY SHUT DOWN FEATURE.  
MANUAL SHUT DOWN / ENABLE CIRCUIT:  
The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of the  
Remote Start Unit regardless of the RF transmitter operation.  
To test the integrity of the manual shut down / enable circuit:  
1. Place the control switch in the on (Closed To Ground) position.  
2. Start the vehicle using the RF transmitter.  
3. The vehicle should start and run under the control of the remote start unit.  
4. Move the switch to the off (Open From Ground) position, the vehicle should shut off.  
If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire of  
the Audiovox Remote Start Unit. If you have a plug in enable switch, check that the two pin connector is  
firmly seated in the mating connector on the control module.  
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE  
OPERATION OF THE MANUAL SHUT DOWN / ENABLE FEATURE.  
NEUTRAL START SAFETY TEST:  
The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any  
position other than Park, or Neutral. When installing a Remote Start Device, it is imperative that the Yellow  
Starter wire be connected to the ignition switch side of the Neutral Start Switch. Consideration for the  
placement of a starter inhibit relay is important as well, and should be connected to the ignition switch side  
of the Yellow Start Wire.  
20  
128-6531  
20 of 24  
 
To test the integrity of the Neutral Start Safety Circuit:  
1. Set the vehicle parking brake.  
2. Block the drive wheels to prevent vehicle movement.  
3. Temporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch.  
4. Sitting in the vehicle, start the engine using the vehicle's ignition key.  
5. Step on the brake pedal and shift the gear selector into reverse.  
6. Allow the transmission to shift. When you feel the engine pull, do not move the gear selector just turn the  
ignition switch off. DO NOT attempt to remove the key.  
7. Keeping the brake pedal depressed, activate the RF transmitter in an attempt to start the vehicle. The  
car should not start.  
8. Repeat the above test this time move the gear selector to the drive position. If the unit attempts to start,  
failing this test, recheck your Yellow Wire's connection. This wire must be connected to the ignition  
switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical  
Neutral Safety Switch, it will be necessary to reconfigure the Remote Starts Wiring to accommodate this  
vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you  
to determine if the vehicle you are working on has this type of safety switch and will provide alternate  
wiring methods to accommodate this situation.  
MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:  
Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of  
safety when installing a remote start device. Often when the ignition switch is turned off while the gear  
selector is in any position other than park or neutral, the mechanical function will not allow the key to be  
turned to the start position or be removed from the ignition cylinder. This configuration prevents mechanical  
operation while the vehicle is in gear but offers no consideration for electrical operation. Because of this  
potential problem, this installation requires the additional connection of a safety wire from the remote start  
device to the vehicle Park/Neutral ECM Input or the vehicle key in sensor. This connection will prevent  
remote start operation if the key is left in the ignition switch regardless of the gear selectors position.  
PARK / NEUTRAL ECM INPUT:  
The Park/Neutral ECM input is the preferred method of installation. This not only maintains the integrity of the  
factory circuit, it is also the easiest to install, providing the vehicle you are working on has this ECM input.  
The installation required for this application (shown below), indicates the slight reconfiguration of the control  
switch wiring and the addition of a 4000 series diode. Shown is a typical GM Park/Neutral ECM input circuit.  
To connect the Audiovox remote start unit to the GM Park / Neutral ECM input:  
1. Locate the Orange / Black reference wire in the "C2" connector found at the ECM in GM B Body vehicles  
or, locate the equivalent reference wire in the vehicle you are installing the Audiovox Remote Start Unit in.  
2. Connect the Cathode, (Striped) end, of a 4000 series diode to this reference wire.  
3. Connect the Anode, (Non Striped) end, of the diode to one side of the Remote Start j enable switch.  
4. Connect the other side of the enable switch to the Black/White enable input wire of the Remote Start unit.  
The reference diagram below shows a typical GM B Body ECM reference wire and how it is to be connected  
to the Remote Start Unit.  
CAUTION!  
REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY  
DISCONNECTED IN STEP 3  
21  
128-6531  
21 of 24  
 
DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE  
OPERATION OF THE NEUTRAL SAFETY START FEATURE.  
KEY IN SENSOR CIRCUITS:  
If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two  
alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a  
margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear.  
AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The  
following two circuits may be used only if the above circuit is not available.  
NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts  
the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut  
down. This must be explained to the operator as it is in contrast to the normal operation of a vehicle  
utilizing an electrical neutral start switch and is inconsistent with the operators manual.  
Additional information concerning Key In Sensor methods 1 & 2 are listed below and should be reviewed  
before considering either alternative.  
Method 1 will allow the safety required for the remote start unit and prevent the vehicle from starting while in  
any gear other than Park or Neutral while the key is in the ignition cylinder however, if the key is left in the  
ignition switch and the door is left opened, the added relay will be energized causing a 150mA drain on the  
battery.  
Method 2 will allow the safety required for the remote start unit and prevent the vehicle from starting while in  
any gear other than Park or Neutral while the key is in the ignition cylinder however, the original factory key in  
chime module will not alert the owner that the key has been left in the ignition switch. In addition, this may  
also effect other warning tones such as the light on reminder.  
These situations should be carefully considered before altering the vehicle's wiring and must be fully ex-  
plained to the consumer.  
METHOD 1  
To connect to the key in sensor as shown in method 1:  
A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.  
B. Cut this wire and connect the ignition cylinder side to chassis ground.  
C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .  
D. Cut this wire and connect the ignition cylinder side to terminal 30 of a P&B VF45F11 or equivalent relay.  
E. Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped)  
side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit.  
F. Connect terminal 86 of the relay to a fused +12 volt constant battery source.  
G. Connect terminal 87 of the relay to the Chime Module side of the previously cut wire in step D.  
H. Connect terminal 85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B.  
NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down  
circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side  
must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be  
connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to  
use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown in this installation  
guide. (Page 9)  
22  
128-6531  
22 of 24  
 
METHOD 2  
To connect to the key in sensor circuit as shown for method 2:  
A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.  
B. Cut this wire and connect the ignition cylinder side to chassis ground.  
C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .  
D. Cut this wire and connect the ignition cylinder side to the Remote Start Negative Safety Shut down Wire  
Gray/Black, using a 4002 series diode as shown above.  
NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down  
circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side  
must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be  
connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to  
use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown in this installation  
guide. (Page 9)  
AFTER THE CONNECTION OF THE NEUTRAL START SAFETY WIRE AS INDICATED IN ANY OF THE  
PREVIOUS ALTERNATE CONFIGURATIONS, THIS CIRCUIT MUST BE TESTED FOR OPERATION.  
Retest by following the steps outlined in the NEUTRAL START SAFETY TEST shown in this manual.  
COMPLETING THE INSTALLATION:  
After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of  
the system:  
NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has  
delay interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with this  
type of interior light, we suggest you learn the interior light delay.  
To learn the light delay, start with all doors closed:  
(1) Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system.  
The LED turns on solid to confirm the system entered the learn mode.  
(2) Immediately open and close the door of the vehicle to initiate the dome delay.  
The unit will monitor the door trigger input Positive, (Purple), and Negative, (Brown) when active.  
When the dome light turns off, the unit will add 2 seconds then exit the learn mode.  
(3) The LED will begin flashing the Armed indication indicating the unit has exited the learn mode and is  
armed.  
1. If you have not done so already, place the red rubber handle cover over the handle of the control switch for  
ease of identification. This will allow your customer to distinguish the Remote Start control switch from the  
program switch.  
2. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain  
that the chosen mounting location will not inhibit any of the controls of the vehicle.  
3. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in  
contact with under the dash board or in the engine compartment areas.  
CAUTION: Particularly avoid the area around the steering shaft and column, as wires can wrap around these  
mechanisms and impair the safe operation of the vehicle.  
4. Apply the Caution Labels supplied with this kit to a conspicuous area in the engine compartment. Make  
sure to clean the surface before affixing the label.  
5. Check the vehicle's wipers, lights, horn, etc.... to insure proper operation.  
6. Replace all panels that were removed during installation, and retest the system.  
7. Explain all activated features and safety systems associated with Remote Start Unit installed to the  
customer.  
8. Place the Valet Switch Tag and or the Remote Start Control Switch Tag on their respective switches and  
point these out to the customer.  
23  
128-6531  
23 of 24  
 
© 2003 Audiovox Electronics Corp., Hauppauge, N.Y. 11788  
128-6531  
128-6531  
24 of 24  
 

3Com Pet Fence 3CR100AV97 User Manual
3M Marine Instruments eg3 User Manual
Acumen Watch Hydra Alert Jr User Manual
AEG Washer 48380 User Manual
Aiphone Speaker System LEM 1L User Manual
Allied Telesis Network Card AT 2874SX User Manual
American Audio Musical Instrument WM 700HH User Manual
Avenview Switch SW HDM3D C5 8X8 User Manual
Axis Communications Security Camera M3007PV User Manual
Axis Communications Security Camera P3367 VE User Manual