American Standard Hot Tub 2425XXXW LHO User Manual

HAMPTON 5' x 32"™  
INTEGRAL APRON WITH  
REMOVABLE ACCESS PANEL  
HIGH GLOSS ACRYLIC  
2425.XXXW-LHO  
2425.XXXW-RHO WHIRLPOOL  
INSTALLATION INSTRUCTIONS  
SHOWN LESS ALL FITTINGS  
THANK YOU...  
60  
(1524mm)  
12  
for selecting an American Standard bath. Your new bath is shipped to  
WATER  
RETENTION  
FLANGE  
(305mm)  
10-1/4  
you after careful inspection. the whirlpool version is completely  
assembled with pump, motor, and system piping. All you need to finish  
the installation are your selected fittings and electrical connections for  
a whirlpool. To insure maximum performance and pleasure from this  
(260mm)  
3/4  
(8) JETS  
(19mm)  
(3 SIDES)  
FINISHED  
WALL  
SEE FITTING  
SPECS FOR  
DIMENSIONS  
16  
(406mm)  
product, please follow the instructions and cautions.  
9
(229 mm)  
List of Optional Components (not included):  
• Safe-T-Heater 9075.120*  
ON/OFF  
SWITCH  
PUMP  
32  
(813mm)  
CUTOUT IN FLOOR FOR DRAIN  
List of Required Components (not included):  
ACCESS TO PUMP/MOTOR  
THROUGH REMOVABLE  
FRONT ACCESS PANEL  
C/L OF  
SUPPLIES  
(2) AIR VALVES  
C/L OF  
3
• Drain 1583.470*  
• Bath Filler*  
(76mm)  
C/L OF DRAIN  
* see your American Standard Dealer  
SHOWER ARM  
FINISHED  
WALL  
OPTIONAL TO  
FINISHED FLOOR  
USUALLY BETWEEN  
65 & 78  
SAFE-T-HEATER  
REMOVABLE  
BLANK  
1" WATER  
RETENTION  
FLANGE  
C/L OF  
VALVES  
List of Required Tools and Supplies:  
(1651 & 1981mm)  
(3 SIDES)  
C/L OF  
SPOUT  
12  
(305mm)  
C/L OF  
OVERFLOW  
OPT.  
Tools  
Supplies  
4
TILING  
FLANGE  
LEVELING STRINGER  
NOT FOR SUPPORT  
3-1/2  
(89mm)  
(102 mm)  
• Level  
• Nails  
• Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Standard  
Woodworking Tools  
• Personal Safety  
Equipment  
• Putty  
TOP OF  
DECK  
UNDERSIDE  
OF DECK  
21-1/4  
21-1/2  
(546mm)  
• Caulking (waterproof)  
• 1 x 3 or 2 x 2  
Stringers  
(540mm)  
REF.  
DIM  
ROUGH  
FLOOR  
BATH  
SUPPORT  
MATERIAL  
1-1/2 N.P.T.M.  
THREADS  
• Drop Cloth  
• 15 amp GFI  
Outlet  
2-3/4  
(70mm)  
1-1/2 O.D.TAILPIECE  
4-5/8  
(117mm)  
• Cement, Plaster,  
Grout  
• Caulking Gun  
Left-hand version shown  
GENERAL SPECIFICATIONS FOR 2425 WHIRLPOOL  
General Installation Information  
INSTALLED SIZE  
WEIGHT  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
WHIRLPOOL MIN. OPERATING VOL.  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
60 x 32 x 21-1/2 (1524 x 813 x 546mm)  
115 Lbs. (52 Kg.)  
Carefully uncrate and inspect your new bath for any shipping damage.  
If such damage is found, report it to your vendor immediately. After  
inspection and during installation, protect the bath from construction  
damage. Before installation, and before enclosing with wallboard,  
tile, etc., water test the unit and check for leaks. Do not make  
modifications to the whirlpool system or remove pump from factory  
mounting. This could adversely affect the safety and performance of  
the whirlpool and void the warranty. Do not handle or move the  
whirlpool by the pump, motor, or piping system. Fittings (bath filler,  
shower arm, etc.) are not provided with the bath and must be ordered  
separately. Framing and enclosing materials are provided by others.  
574 Lbs. (258 Kg.)  
55 Gal. (208 L.)  
45 Gal. (171 L.)  
16-1/4 x 38-1/4 (413 x 972mm)  
26-1/4 x 52-1/2 (667 x 1334mm)  
15 (381mm)  
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)  
(PROJECTED AREA)  
PTS.  
CUBE (FT3)  
20.8  
35.3  
WHIRLPOOL ELECTRICAL SPECIFICATIONS  
PUMP  
1.6 HP, 9.7 AMPS,120V.  
IMPORTANT: Water test unit before installation and  
enclosure!  
General Installation Information  
Bath may only be installed in a recess type installation.  
Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made  
through access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as  
indicated. this bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position  
bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary. To secure the tub to wood studs use  
drywall screws w/washers or roofing nails immediately above the flange of the tub.To secure the tub to steel studs use 4" drywall screws and  
flatwashers.  
See page 2 for complete installation information.  
Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against  
the bottom of the tub apron, also holding the tub in place.  
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.  
© American Standard Inc. 2003  
All product names listed herein are trademarks  
of American Standard Inc. unless otherwise noted.  
753456-100 REV. A  
 
ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other  
applicable codes.  
WARNING:  
When using electrical products, basic precautions should always be observed, including the following:  
1. DANGER: RISK OF ELECTRIC SHOCK  
Connect only to a circuit protected by a ground-fault circuit interrupter.  
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.  
3. Install to permit access for servicing.  
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).  
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the  
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded  
neutral wire and a third wire, earth ground, are essential. Heater equipped models require a separate 15 amp maximum  
GFCI circuit. SAFE-T-HEATER EQUIPPED MODELS REQUIRE A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.  
ELECTRICAL INSTALLATION  
SEPARATE  
15 GFCI  
OUTLET  
WHIRLPOOL MOUNTED  
120 VAC  
AIR SWITCH OR  
WALL TIMER  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
(3)  
753456-100 REV. A  
 
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
Motor  
Hi-Performance  
Rating  
50'  
100' 150'  
120V Power Line  
12 10  
200'  
1.6  
electrical codes  
12  
8
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the  
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of  
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings  
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is  
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or  
®
stains may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing  
with a white automotive-type polishing compound and waxing with a liquid wax.  
®
753456-100 REV. A  
(4)  
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
 

3M Intercom System C5000 User Manual
Activision Video Games 47875843929 User Manual
ADTRAN Network Router 1202890E1 User Manual
Advantech Webcam PCA 6774 User Manual
AKG Acoustics Headphones 3052H00040 User Manual
American DJ DJ Equipment dB Display User Manual
Audiovox Automobile Alarm AX 500 User Manual
Avenview TV Cables FO HDMI SET User Manual
Axis Communications Digital Camera 223M User Manual
Ayre Acoustics CD Player CX 7EMP User Manual