USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new
B31 MINI PLUS Keurig® Brewer
CAUTION: There are two sharp needles that
puncture the K-Cup® portion pack, one above the
K-Cup Holder and the other in the bottom of the
K-Cup Holder. To avoid risk of injury, do not put your
fingers in the K-Cup Assembly Housing.
WARNING
WARNING
KEEP ALL PLASTIC BAgS AwAY FROM CHILDREN.
THIS PRODUCT CONTAINS CHEMICALS, INCLUDINg
LEAD, wHICH IS KNOwN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
CAUTION: There is extremely hot water in the K-Cup Holder during
the brew process. To avoid risk of injury, do not lift the Brewer Handle
or open the K-Cup Assembly Housing during the brewing process.
SHORT CORD INSTRUCTIONS: A short power supply cord is
provided to reduce the risk of becoming entangled in or tripping over a
longer cord.
If an extension cord is used, (1) the marked electrical rating of the
cord set or extension cord should be at least as great as the electrical
rating of the appliance; (2) the cord should be arranged so that it will
not drape over the countertop or tabletop where it can be pulled on by
children or tripped over unintentionally; and (3) the extension cord must
include a 3-prong grounding plug.
WaRnInG TO USERS anD PaREnTS
1. DOnOTpermit children to use Brewer without adult
supervision. Brewer dispenses very hot water.
2.SPEcIaLnOTIcEFORHOTcOcOaUSERS: IMMEDIaTELYaFTER
USInGaHOTcOcOaK-cUP, RUnaHotWaterBrewcycle without
a K-Cup to avoid the possibility of clogging the exit needle. DOnOT
assume the next user will do this.
THIS PRODUCT IS FOR HOUSEHOLD USE OnLY.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE
WARNING
BOTTOM COVER. NO USER SERVICEABLE
PARTS ARE INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
!
3
SeCtIon 1 Brewer Overview
table of ContentS
a
B
c
D
E
F
G
H
I
cold Water Reservoir Lid
cold Water Reservoir
BREW Button
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
Model B31 MINI PLUS Using Your Brewer
SECTiON 1—Brewer Overview...........................................................4
SECTiON 2—Helpful Hints..................................................................6
SECTiON 3—Buttons & indicators.........................................................7
add Water/Brewer Handle Indicator
Power Button
SECTiON 4—Set-up & Operation
Initial Cleansing & First Brew...........................................................8
Power cord
Drip Tray Base
SECTiON 5—Cleaning & Maintenance
Cleaning External Parts ..................................................................12
Cleaning the K-Cup® Portion Pack Holder Assembly ................12
Cleaning the Cold Water Reservoir................................................14
Emptying the Internal Hot Water Tank...........................................14
Storage ...............................................................................................14
Storing the Power Cord....................................................................14
De-Scaling Your Brewer ..................................................................15
Drip Tray
Drip Tray Plate
J
Drip Tray Overfill Indicator
K-cup Portion Pack assembly Housing
Brewer Handle
K
L
M
n
O
P
SECTiON 6—Troubleshooting ..........................................................16
Water Level Guide (Inside Cold Water Reservoir)
K-cup Portion Pack Holder
Funnel
SECTiON 7—Warranty ......................................................................18
Record your Brewer Serial number here.
K-cup Portion Pack Holder assembly
Removing the serial number label from the Brewer will void warranty.
4
MMAAXX
MMIINN
M
a
B
c
L
n
D
P
K
O
E
J
I
H
F
G
For replacement parts, please call 1.866.901.BREW (2739).
5
SeCtIon 2 Helpful Hints
Plug Brewer into its own grounded outlet — If the electric circuit is
overloaded with other appliances, your Brewer may not function properly.
The Brewer should be operated on its own circuit, separate from other
appliances.
To guide you, the Brewer includes a Water Level Guide located inside
the Cold Water Reservoir. The Water Level Guide is removable to make
cleaning easy.
Brewing into a tall mug — To brew into a tall mug, simply remove the Drip Tray
initial Cleansing Brew — Before you use your Brewer for the first time,
perform an initial cleansing brew by running clean water through the brew
cycle without using a K-Cup® portion pack.
Assembly and place the tall mug on the Drip Tray Base.
The Drip Tray — Any liquid overflow (from your cup or the Cold Water
Reservoir) will be caught in the Drip Tray. Be sure to empty the Drip Tray
when the red Drip Tray Overflow Indicator pops up. The Drip Tray has a snug
fit to ensure it stays put in transit.
One Cup at a Time — Your new Brewer makes one fresh beverage at a time.
You’ll need to add fresh water each time you brew. Unlike other Keurig
Brewers, the B31 does not store water in the reservoir.
Automatic Shut Off — Your Brewer will shut off automatically when it is idle for
The Right Water Makes a Difference — For the best tasting gourmet coffee,
tea or hot cocoa, Keurig recommends using bottled or filtered water. We
do not recommend using distilled or reverse osmosis water. Water quality
varies from place to place. If you notice an undesirable taste in your cup of
coffee such as chlorine or other mineral taste, we recommend you consider
using bottled water or water from a filtration system.
longer than 90 seconds. Simply press the Power Button to restart.
Clean Your Brewer Regularly — To keep your Brewer looking and performing
its best, be sure to clean the external and internal components on a regular
basis. See page 12 for more information.
De-Scaling — Mineral content in water varies from place to place. Depending
on the mineral content of the water in your area, calcium deposits or scale
may build up in your Brewer. Scale is non-toxic, but left unattended, it can
hinder Brewer performance. De-scaling your Brewer helps maintain the
heating element and other internal parts of the Brewer that come in contact
with water. See page 15 for more information.
Customize your Size, Flavor & Brew — With the choice of over 200 varieties
of K-Cups and multiple fill levels, your Brewer gives you endless options to
customize the size, flavor and strength that’s perfect for you. For a strong,
intense cup, select an Extra Bold K-Cup (with up to 30% more ground coffee
than regular varieties) and brew size that’s right for you. The less water you
use, the more intense flavor in your cup. The more water you use, the less
intense flavor in your cup.
Storing — When storing your Brewer, carefully empty the Drip Tray and make
sure both the Cold Water Reservoir and Internal Hot Water Tank are empty.
Store your Brewer upright in a safe, dry, frost-free environment. See page 14
for more information.
6
SeCtIon 3 Buttons & Indicators
Power Button
BREW Button Indicators
BREW
The Power Button turns your Brewer On and Off.
Flashing Blue — Indicates you are ready to brew
your beverage. Press the BREW Button once to
start the brewing process.
add Water Indicator
Flashing Red — Indicates the water is heating.
Flashing Blue — Indicates you should fill the
Cold Water Reservoir.
Solid Red — Indicates brewing has begun.
Drip Tray Overfill Indicator
A red float will appear when the Drip Tray is
almost full. Carefully slide the Drip Tray out and
empty its contents.
Brewer Handle Indicator
Flashing Blue — Indicates the minimum amount
of water (6 oz.) has been poured into the Cold
Water Reservoir and you’re ready to insert a
K-Cup. Lift the Brewer Handle, insert a K-Cup,
then lower the Brewer Handle completely and
firmly to close.
Your next Brew
When the brewing process is complete, your
Brewer is ready for the next beverage. Begin
the process again, adding fresh water and a
new K-Cup.
Your Brewer will shut off automatically
when it is idle for longer than 90 seconds.
Simply press the Power Button to restart.
7
SeCtIon 4 Set-up & Operation
Initial cleansing & First Brew
MMAAXX
MMIINN
Before
you
Brew
1
2
3
4
Before making your first beverage,
perform an initial cleansing brew.
Follow these steps, skipping
numbers 9 and 10. The initial
cleansing brew is performed
without a K-Cup® portion pack.
Plug the Brewer into its own
Press the Power Button found on
the front of the Brewer.
The Add Water Indicator will
flash blue. Lift the Cold Water
Reservoir Lid to open.
grounded outlet. If the electric circuit
is overloaded with other appliances,
your Brewer may not function
properly. The Brewer should be
operated on its own circuit, separate
from other appliances.
8
MMAAXX
MMIINN
MMAAXX
MMIINN
MMAAXX
MMIINN
5
6
7
Fill the Cold Water Reservoir to the desired fill
level with filtered or bottled water. (We do not
recommend distilled or reverse osmosis water.)
The Brewer Handle Indicator will flash blue when
the minimum water level (6 oz.) is reached.
Close the Cold Water Reservoir Lid.
Place a mug on the Drip Tray Plate.
NOTE: The Drip Tray is not dishwasher safe.
The Brewer has three fill levels – 6 oz.,
8 oz. and 10 oz. For precise measuring,
make sure the Brewer Handle is closed
completely.
If you should happen to over-fill the Cold
Water Reservoir, the overflow will be
caught in the Drip Tray.
The Drip Tray slides out so you can fit
a taller mug!
9
SeCtIon 4 Set-up & Operation (continued)
CAUTION: There are two sharp needles that puncture the K-Cup, one above the K-Cup Holder and the other in the
bottom of the K-Cup Holder. To avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
8
9
10
Lift the Brewer Handle to open.
Water will exit the Cold Water Reservoir
and enter the Brewer.
Select a K-Cup® portion pack.
Do not remove the foil lid or puncture
the K-Cup.
Place the selected K-Cup into the K-Cup
Holder Assembly.
Skip Steps 9 and 10 for the initial
cleansing brew.
Ensure all of the water has left the Cold Water Reservoir and drained into the Brewer before proceeding to Step 11.
10
CAUTION: There is extremely hot water in the K-Cup Holder during the brew process. To avoid risk of
injury, do not lift the Brewer Handle or open the K-Cup Assembly Housing during the brewing process.
2 Min
12
14
11
13
Lower the Brewer Handle completely
and firmly to close.
The BREW Button will flash blue.
Press the BREW Button. It will then
flash red while the water is heating,
and turn solid red when brewing
begins.
The water will reach the correct
temperature in approximately
2 minutes. The BREW Button will
turn solid red and your beverage
will start to dispense.
If you are performing an initial
cleansing brew, discard the water
from the mug and begin at Step 4 to
brew your first beverage.
if you have previously completed an
initial cleansing brew, enjoy your
beverage.
Ensure all of the water has left
the Cold Water Reservoir and
drained into the Brewer before
lowering the Brewer Handle.
Your Brewer is now ready for
the next beverage. Begin the
process again, adding fresh
water and a new K-Cup.
11
SeCtIon 5 Cleaning & Maintenance
cleaning External Parts
cleaning the K-cup® Portion Pack
Holder assembly
IMPORTANT: Make sure the Brewer is unplugged before cleaning.
1. Cleaning the Parts — The K-Cup Holder Assembly can be placed onto the
top shelf of a dishwasher. NOTE: Use low temperature cycles in the
dishwasher. To remove the K-Cup Holder Assembly from the Brewer, lift
the Brewer Handle to open. Grasp the top of the K-Cup Holder with one
hand. With the other hand, push up on the bottom of the K-Cup Holder
until it releases (fig. 1). After cleaning, align the K-Cup Holder with the
opening using the two front ribs as a guide, and snap into place from the
top (fig. 2).
Regular cleaning of the Brewer’s external components is recommended.
1. Never immerse the Brewer in water or other liquids. The Brewer
housing and other external components should be cleaned with a damp,
non-abrasive, lint-free cloth.
2. The Drip Tray and Drip Tray Plate should be periodically inspected and
cleaned with a damp, non-abrasive, lint-free cloth. The Drip Tray and Drip
Tray Plate should not be put into the dishwasher. To remove the Drip Tray,
simply slide it toward you. Remember, when the red Drip Tray Overfill
Indicator appears, the Drip Tray is almost full. Carefully remove the Drip
Tray and discard its contents.
fig.
fig.
1
2
The Drip Tray has a snug fit to ensure it stays put in transit.
12
2. Cleaning the Funnel — The Funnel can be removed from the
K-Cup Holder by pulling on it until it snaps off (fig. 3). The Funnel
can be placed on the top shelf of a dishwasher. NOTE: Use low
temperature cycles in the dishwasher. To replace the Funnel, just snap it
back onto the K-Cup Holder Assembly.
CAUTION: There are sharp needles that puncture the K-Cup above the
K-Cup Holder and in the bottom of the K-Cup Holder. To avoid risk of
injury, do not put your fingers in the K-Cup Assembly Housing.
NOTE: Over time, discoloration, spotting or staining may appear in the
Cold Water Reservoir. This is normal and will vary depending on the
mineral content of the bottled or filtered water used. This will not affect
the operation of the Brewer. However, be sure to clean the Cold Water
Reservoir regularly to minimize build-up (see page 14).
3. Cleaning the Exit Needle — The Exit Needle is located on the inside
bottom of the K-Cup Holder Assembly. Should a clog arise due to coffee
grinds, it can be cleaned using a paper clip or similar tool. Remove
K-Cup Holder Assembly and detach Funnel. Insert the paper clip (fig. 4)
into the Exit Needle to loosen the clog and push it out. The K-Cup Holder
can be placed on the top shelf of a dishwasher. NOTE: Use low
temperature cycles in the dishwasher. The Entrance Needle does not
require cleaning.
fig.
fig.
3
4
!
13
SeCtIon 5 Cleaning & Maintenance (continued)
cleaning the cold Water Reservoir
Storage
To access the Cold Water Reservoir, lift the Cold Water Reservoir Lid.
Remove the Water Level Guide (fig. 5), then clean the inside of the reservoir
with a damp, lint-free cloth as necessary (fig. 6). Replace the Water Level
Guide and close the Cold Water Reservoir Lid when finished. NOTE: The Water
Level Guide is not dishwasher safe.
Empty the Internal Hot Water Tank and Cold Water Reservoir before
storing. Ensure that you store your Brewer in a safe and frost-free
environment, and in an upright position. Storing the Brewer in cold
temperatures may cause condensation to freeze inside the Brewer
and cause damage.
Before using your Brewer after storage, wipe the Cold Water Reservoir
with a damp, lint-free cloth and run three cleansing brews without a
K-Cup® portion pack. See page 8 for more information.
fig.
fig.
5
6
If your Brewer has been in an environment below freezing, allow the
Brewer to rest at room temperature for at least 2 hours before
powering on.
Storing the Power cord
Behind the Brewer is a convenient compartment that will hold the
Power Cord (fig. 7). This makes the Brewer both easier to store and easier
to take on the go.
Emptying the Internal Hot Water Tank
fig.
7
1. Brewer must be powered off and plugged in.
2. Ensure that the Cold Water Reservoir Lid is closed.
3. Place a mug on the Drip Tray, then press and hold the BREW Button
until all the water has been dispensed. NOTE: There will be a delay of
3–4 seconds before water begins to dispense.
14
De-Scaling Your Brewer
Depending on the mineral content of the water, calcium deposits or scale
may build up in your Brewer. Scale is non-toxic but left unattended, it can
hinder Brewer performance. De-scaling your Brewer helps maintain the
heating element and other internal parts of the Brewer.
C. RiNSE
Step 1: After the prescribed period of time (at least 30 minutes), turn your
Brewer on and place the ceramic mug on the Drip Tray Plate. Lift and
lower the Brewer Handle completely and perform a brew without
adding a K-Cup. Empty the contents of the ceramic mug into the sink.
CAUTION: Be careful as contents will be hot.
The Brewer should be de-scaled every 3-6 months to ensure optimal
performance or when there are white deposits in the Cold Water Reservoir.
It is possible for calcium deposits to build up faster, making it necessary to
de-scale more often.
Step 2: Fill the Cold Water Reservoir with 10 ounces of fresh water, place
the ceramic mug on the Drip Tray Plate and perform a brew without
adding a K-Cup.
A. PREPARE
You will need 20 oz. of undiluted white vinegar, a 12 oz. ceramic mug (do not
use a paper cup) and access to a sink.
Step 3: Repeat Step 2 three times to cleanse the Brewer plumbing and get rid
of any residual taste from the vinegar. The Brewer is now ready for
normal use again.
B. FiLL AND CLEAN
Step 1: Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar to
the 10 oz. mark on the Water Level Guide.
Service
Step 2: Place the ceramic mug on the Drip Tray Plate. Lift and lower the
Brewer Handle completely and perform a brew without adding a
K-Cup. Empty the contents of the ceramic mug into the sink.
CAUTION: Be careful as contents will be hot.
Beyond these recommended cleaning and maintenance procedures, this
Brewer is not user serviceable. For service, please refer to the Warranty
section in this guide.
Step 3: Place the ceramic mug back on the Drip Tray Plate. Pour the
remaining 10 oz. of vinegar into the Cold Water Reservoir. Start a brew,
but power off the Brewer just after it starts to dispense. Allow it to sit
for at least 30 minutes.
15
SeCtIon 6 Troubleshooting
SiTUATiON
SOLUTiON
Brewer does not have power
• Make sure the Power Button is pressed. The Add Water Indicator
should flash blue after pushing the Power Button.
• Plug Brewer into an independent outlet.
• Check to be sure that it is plugged in securely.
• Plug into a different outlet.
• Reset your home’s circuit breaker if necessary.
Brewer will not brew when used for the first time
Brewer will not brew
• Brewer may be cold or frozen. Let Brewer rest at room temperature for at
least 2 hours before powering on.
• Make sure the Brewer has power (see above).
• Press the Power Button. If the Add Water Indicator flashes blue, add water
and attempt to brew. If the Add Water Indicator does not flash blue, make
sure the Brewer has power (see above). If the Brewer still does not operate,
contact Customer Service.
• If the BREW Button flashes red longer than 3 minutes, contact Customer
Service.
16
SiTUATiON
SOLUTiON
Brewer only brews a partial brew
• The Exit Needle may be clogged (see page 13).
• Clean the K-Cup® Portion Pack Holder Assembly if necessary (see page 12).
• De-scale the Brewer (see page 15).
• If you have repeated the de-scale procedure two times, and the Brewer
still does not function properly, contact Customer Service.
Brewer shuts off automatically
There is water in the Drip Tray
• In normal operation, the Brewer will shut off when it is idle for longer
than 90 seconds. Just press the Power Button to restart.
• If the Brewer shuts off in the middle of a brew, contact Customer Service.
• Remember that any liquid overflow (from your cup or the Cold Water
Reservoir) will be caught in the Drip Tray.
• When the Drip Tray is almost full, the red Drip Tray Overflow Indicator will
appear. Carefully remove the Drip Tray and empty its contents into the sink.
Red indicator appears in Drip Tray
• This means the Drip Tray is almost full. Carefully remove the Drip Tray
and empty its contents into the sink.
Should other issues arise with your Brewer, please call
Keurig Customer Service at 1.866.901.BREW (2739).
17
SeCtIon 7 Warranty
Limited One Year Warranty
Keurig® warrants that your Brewer will be free of defects in materials or
workmanship under normal use for one year from the date of purchase. It is
recommended that you fill out and return the warranty card enclosed with
your Brewer so that your purchase information will be stored in our system.
Keurig will, at its option, repair or replace the Brewer without charge upon its
receipt of proof of the date of purchase. If a replacement Brewer is necessary
to service this warranty, the replacement Brewer may be new or
reconditioned. If a replacement Brewer is sent, a new limited one year
warranty will be applied to the replacement Brewer.
Other limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO
YOUR B31 BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT
ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or
provinces do not allow disclaimers of such implied warranties or limitations
on how long an implied warranty lasts, so the above limitation may not apply
to you depending on the state or the province of purchase.
This warranty only applies to Brewers operated in the United States and
Canada. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state and, in the case of Canada, from
province to province.
How do you obtain warranty service?
Keurig Brewers are high-quality appliances and, with proper care, are
intended to provide years of satisfying performance. However, should the
need arise for warranty servicing, simply call Keurig Customer Service at
our toll free phone number 1.866.901.BREW (2739). Please do not return your
Brewer for servicing without first speaking to Keurig Customer Service to
obtain an Authorization to Return number (ATR). Keurig Brewers returned
without an ATR number will be returned to the sender without servicing.
What is not covered by the limited warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER
INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH
OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces
do not allow the exclusion or limitations of incidental or consequential
damages, so the above limitation or exclusion may not apply to you
depending on the state or province of purchase.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)
Nor does this warranty cover damages caused by services performed by
anyone other than Keurig or its authorized service providers, use of parts
other than genuine Keurig parts, or external causes such as abuse, misuse,
inappropriate power supply or acts of God.
18
P/N 60-201172-000 RevB
11/09
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
Keurig, Incorporated is a wholly-owned subsidiary of
Green Mountain Coffee Roasters, Inc.
cLIcK, caLL OR SHOP I www.keurig.com I 1.866.901.BREW I At over 17,000 stores in the U.S. and Canada
FOR HOUSEHOLD USE ONLY
Covered by U.S. Patent Number 7,165,488 and
other U.S. and foreign patents pending.
Made and printed in China
© 2009 Keurig, Incorporated
All rights reserved.
|